HYDRAULIC SYSTEM
VALVE GP-SHUTTLEVALVE GP-SOLENOID
IMPLEMENTS
BRACE GPC-FRAME GP
BULLDOZER GP
HYDRAULIC SYSTEM
VALVE GP-SHUTTLE
#SEBP58180450
4T-1860: VALVE GP-SHUTTLE
4T-1860 VALVE GP-SHUTTLE
S/N DSH1-UP; DLN1-UP; DJR1-UP
PART OF 271-4967, 271-4968, 271-4969, 308-6726 VALVE GP-CONTROL
ALSO AN ATTACHMENT
S/N DSH1-UP; DLN1-UP; DJR1-UP
PART OF 271-4967, 271-4968, 271-4969, 308-6726 VALVE GP-CONTROL
ALSO AN ATTACHMENT
For full view, you need register
#SEBP58180451
201-0950: VALVE GP-SOLENOID
201-0950 VALVE GP-SOLENOID
S/N DSH1-UP; DLN1-UP; DJR1-UP
24-VOLT
PART OF 226-4751, 520-2181 MANIFOLD GP-CONTROL, 234-5126 VALVE & MTG GP-BULLDOZER
ALSO AN ATTACHMENT
S/N DSH1-UP; DLN1-UP; DJR1-UP
24-VOLT
PART OF 226-4751, 520-2181 MANIFOLD GP-CONTROL, 234-5126 VALVE & MTG GP-BULLDOZER
ALSO AN ATTACHMENT
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 122-1133 | [1] | COIL AS (24-VOLT) | |
| 1S-9593 | [2] | STRAP-CABLE | ||
| 186-3735 | [2] | PIN-CONNECTOR (16-GA TO 18-GA) | ||
| 102-8802 | [1] | KIT-RECEPTACLE (2-PIN) | ||
| (INCLUDES RECEPTACLE AS & WEDGE) | ||||
| 2. | 156-5970 | [1] | NUT (1/2-20-THD) | |
| 3. | 171-8772 | [1] | VALVE AS-SOLENOID | |
| 156-5970 | [1] | NUT (1/2-20-THD) | ||
| AVAILABLE REPAIR KIT(S): | ||||
| 195-7430 | KIT-SEAL (SOLENOID VALVE) | |||
| (INCLUDES O-RING SEALS & BACKUP RINGS) | ||||
#SEBP58180452
341-9214: VALVE GP-SOLENOID
341-9214 VALVE GP-SOLENOID
S/N DSH1-UP; DLN1-UP; DJR1-UP
24-VOLT
PART OF 234-5126 VALVE & MTG GP-BULLDOZER
AN ATTACHMENT
S/N DSH1-UP; DLN1-UP; DJR1-UP
24-VOLT
PART OF 234-5126 VALVE & MTG GP-BULLDOZER
AN ATTACHMENT
For full view, you need register
#SEBP58180453
418-2466: BRACE GP-BULLDOZER
418-2466 BRACE GP-BULLDOZER
S/N DSH1-UP; DJR1-UP
PART OF 418-2465 INSTALLATION AR-BULLDOZER
AN ATTACHMENT
S/N DSH1-UP; DJR1-UP
PART OF 418-2465 INSTALLATION AR-BULLDOZER
AN ATTACHMENT
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1U-0873 | [2] | PIN | |
| 2. | 1U-1212 | [2] | CAP | |
| 3. | 3G-0911 B | [52] | SHIM (0.8-MM THK) | |
| 4. | 4F-1252 | [2] | PIN | |
| 5. | 4F-2710 | [4] | NUT (3/4-10-THD) | |
| 6. | 4T-5495 | [2] | STUD-BALL | |
| 7. | 4T-6211 | [1] | ARM AS (LH) | |
| 7A. | 9W-1677 | [1] | BEARING | |
| 1U-1220 | [1] | PLATE AS | ||
| 8P-9770 | [1] | PLATE | ||
| 8E-5701 B | [14] | SHIM (0.8-MM THK) | ||
| 8. | 4T-6212 | [1] | ARM AS (RH) | |
| 8A. | 9W-1677 | [1] | BEARING | |
| 1U-1220 | [1] | PLATE AS | ||
| 8P-9770 | [1] | PLATE | ||
| 8E-5701 B | [14] | SHIM (0.8-MM THK) | ||
| 9. | 4T-8088 | [2] | SCREW | |
| 10. | 5P-0370 | [2] | LOCK PIN | |
| 11. | 6J-5342 | [2] | RETAINER | |
| 12. | 8E-5701 B | [52] | SHIM (0.8-MM THK) | |
| 13. | 9T-6113 Y | [2] | CYLINDER GP-DUAL TILT | |
| 14. | 160-6306 | [2] | CAP-BEARING | |
| 15. | 7X-0365 | [4] | BOLT (3/4-10X1.5-IN) | |
| 16. | 7X-0388 | [8] | BOLT (7/8-9X4.5-IN) | |
| 17. | 8T-8925 | [4] | BOLT (3/4-10X4.75-IN) | |
| B | USE AS REQUIRED | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP58180454
4T-6135: C-FRAME GP-POWER ANGLING
4T-6135 C-FRAME GP-POWER ANGLING
S/N DSH1-UP; DJR1-UP
PART OF 418-2465 INSTALLATION AR-BULLDOZER
AN ATTACHMENT
S/N DSH1-UP; DJR1-UP
PART OF 418-2465 INSTALLATION AR-BULLDOZER
AN ATTACHMENT
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 6Y-7474 | [1] | PIN-PIVOT | |
| 2. | 9W-7602 B | [52] | SHIM (0.8-MM THK) | |
| 3. | 9X-8258 C | [4] | WASHER (33X56X6-MM THK) | |
| 4. | 193-3063 C | [2] | CAP AS-BEARING | |
| 5. | 195-6283 CM | [4] | NUT-SQUARE (M30X3.5-THD) | |
| 6. | 1U-0725 | [1] | RETAINER | |
| 7. | 3E-9850 CM | [4] | BOLT (M30X3.5X220-MM) | |
| 8. | 8T-9398 | [2] | BOLT (3/4-10X1.75-IN) | |
| 9. | 9W-9009 | [1] | FRAME AS | |
| 10. | 9W-9001 | [1] | ADAPTER AS | |
| 11. | 8E-5486 | [2] | BUSHING | |
| 12. | 5M-6214 | [1] | PLUG (1/8-27 PTF) | |
| 13. | 9W-5375 | [2] | BAR | |
| 14. | 6I-8066 | [1] | TRUNNION AS | |
| 15. | 8E-9575 | [1] | TRUNNION AS | |
| (EACH TRUNNION AS INCLUDES) | ||||
| 7J-5131 | [1] | TRUNNION | ||
| 16. | 9W-4897 | [6] | BRACKET AS | |
| 17. | 8P-9770 | [1] | PLATE | |
| 18. | 1J-6740 | [2] | BEARING AS | |
| 9W-7602 B | [28] | SHIM (0.8-MM THK) | ||
| B | USE AS REQUIRED | |||
| C | CHANGE FROM PREVIOUS TYPE | |||
| M | METRIC PART | |||
#SEBP58180455
365-5514: INSTALLATION AR-BULLDOZER
365-5514 INSTALLATION AR-BULLDOZER -SEMI-UNIVERSAL
S/N DSH1-UP; DJR1-UP
AN ATTACHMENT
S/N DSH1-UP; DJR1-UP
AN ATTACHMENT
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1U-0872 | [2] | PIN | |
| 2. | 4Y-8450 | [1] | GUARD GP-CYLINDER | |
| 4Y-8435 | [1] | GUARD | ||
| 5P-2228 | [4] | BOLT (1/2-13X1-IN) | ||
| 8T-4223 | [4] | WASHER-HARD (13.5X25.5X3-MM THK) | ||
| 3. | 6J-5342 | [2] | RETAINER | |
| 4. | 8E-6754 | [2] | CONNECTOR AS | |
| (EACH INCLUDES) | ||||
| 4A. | 8E-6755 | [2] | BUSHING | |
| 4B. | 8E-6756 | [2] | BUSHING | |
| 5. | 251-9346 | [1] | TRUNNION GP-BULLDOZER | |
| 7X-0349 | [32] | BOLT (5/8-11X3-IN) | ||
| 8T-4122 | [32] | WASHER-HARD (17X32X3.5-MM THK) | ||
| 5A. | 250-1984 | [2] | TRUNNION | |
| 6. | 386-0187 Y | [1] | PUSH ARM GP-STABILIZER | |
| 7. | 386-6977 Y | [1] | LINES GP-TILT CYLINDER | |
| 8. | 7X-0365 | [4] | BOLT (3/4-10X1.5-IN) | |
| 8T-7371 F | [1] | PLATE-SERIAL NUMBER (BLADE) | ||
| (ON BACK OF MOLDBOARD AT RIGHT END NEAR TOP) | ||||
| 4B-4158 F | [2] | SCREW-DRIVE (NO 4X0.25-IN) | ||
| F | NOT SHOWN | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP58180456
365-5517: INSTALLATION AR-BULLDOZER
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1U-0872 | [2] | PIN | |
| 2. | 4Y-8450 | [1] | GUARD GP-CYLINDER | |
| 4Y-8435 | [1] | GUARD | ||
| 5P-2228 | [4] | BOLT (1/2-13X1-IN) | ||
| 8T-4223 | [4] | WASHER-HARD (13.5X25.5X3-MM THK) | ||
| 3. | 6J-5342 | [2] | RETAINER | |
| 4. | 8E-6754 | [2] | CONNECTOR AS | |
| (EACH INCLUDES) | ||||
| 4A. | 8E-6755 | [2] | BUSHING | |
| 4B. | 8E-6756 | [2] | BUSHING | |
| 5. | 251-9346 | [1] | TRUNNION GP-BULLDOZER | |
| 7X-0349 | [32] | BOLT (5/8-11X3-IN) | ||
| 8T-4122 | [32] | WASHER-HARD (17X32X3.5-MM THK) | ||
| 5A. | 250-1984 | [2] | TRUNNION | |
| 6. | 386-0221 Y | [1] | PUSH ARM GP-STABILIZER | |
| 7. | 387-8195 Y | [1] | LINES GP-TILT CYLINDER | |
| 8. | 7X-0365 | [4] | BOLT (3/4-10X1.5-IN) | |
| 8T-7371 F | [1] | PLATE-SERIAL NUMBER (BLADE) | ||
| (ON BACK OF MOLDBOARD - NEAR TOP AT RIGHT END) | ||||
| 4B-4158 F | [2] | SCREW-DRIVE (NO 4X0.25-IN) | ||
| F | NOT SHOWN | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP58180457
418-2465: INSTALLATION AR-BULLDOZER
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1U-1204 | [4] | BEARING | |
| 2. | 4J-9118 | [1] | RETAINER | |
| 3. | 4T-6135 Y | [1] | C-FRAME GP-POWER ANGLING | |
| 4. | 6Y-6752 | [1] | PIN | |
| 5. | 9U-8547 Y | [1] | LINES GP-TILT CYLINDER | |
| 6. | 251-9346 | [1] | TRUNNION GP-BULLDOZER | |
| 7X-0349 | [32] | BOLT (5/8-11X3-IN) | ||
| 8T-4122 | [32] | WASHER-HARD (17X32X3.5-MM THK) | ||
| 250-1984 | [2] | TRUNNION | ||
| 7. | 418-2466 Y | [1] | BRACE GP-BULLDOZER | |
| 8. | 7X-0344 | [1] | BOLT (5/8-11X1.375-IN) | |
| 9. | 7X-0384 | [16] | BOLT (7/8-9X3-IN) | |
| 5P-4963 FY | [1] | PLATE & FILM GP | ||
| F | NOT SHOWN | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP58180458
386-0210: LINK GP-STABILIZER
386-0210 LINK GP-STABILIZER
S/N DSH1-UP; DJR1-UP
PART OF 386-0187 PUSH ARM GP-STABILIZER
AN ATTACHMENT
S/N DSH1-UP; DJR1-UP
PART OF 386-0187 PUSH ARM GP-STABILIZER
AN ATTACHMENT
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9T-0065 B | [52] | SHIM (0.8-MM THK) | |
| 2. | 160-6304 | [2] | CAP-BEARING | |
| 3. | 386-0211 | [1] | LINK AS | |
| 5P-8112 | [2] | GROMMET | ||
| 8P-9770 | [1] | PLATE | ||
| 3A. | 9T-0064 | [2] | BEARING | |
| 9T-0065 B | [28] | SHIM (0.8-MM THK) | ||
| 4. | 6V-8182 | [8] | NUT (3/4-10-THD) | |
| 5. | 7X-0377 | [8] | BOLT (3/4-10X6.5-IN) | |
| B | USE AS REQUIRED | |||
#SEBP58180459
386-0222: LINK GP-STABILIZER
386-0222 LINK GP-STABILIZER
S/N DLN1-UP
PART OF 386-0221 PUSH ARM GP-STABILIZER
AN ATTACHMENT
S/N DLN1-UP
PART OF 386-0221 PUSH ARM GP-STABILIZER
AN ATTACHMENT
For full view, you need register
Parts for your D7R XR TRACK-TYPE TRACTOR:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9T-0065 B | [52] | SHIM (0.8-MM THK) | |
| 2. | 160-6304 | [2] | CAP-BEARING | |
| (EACH INCLUDES) | ||||
| 9T-0065 B | [14] | SHIM (0.8-MM THK) | ||
| 3. | 386-0223 | [1] | LINK AS | |
| 5P-8112 | [2] | GROMMET | ||
| 8P-9770 | [1] | PLATE | ||
| 3A. | 9T-0064 | [2] | BEARING | |
| 9T-0065 B | [28] | SHIM (0.8-MM THK) | ||
| 4. | 6V-8182 | [8] | NUT (3/4-10-THD) | |
| 5. | 7X-0377 | [8] | BOLT (3/4-10X6.5-IN) | |
| B | USE AS REQUIRED | |||
