AVSPARE.COM
parts catalog

342-6646 PISTON & ROD GP S/N MME1-UP 17.0:1 COMPRESSION RATIO PART OF 347-0103, 528-7187 ENGINE AR-CORE 12M 2


BASIC ENGINE
PISTON & ROD GP
CYLINDER BLOCK GP
CYLINDER HEAD GP
CYLINDER BLOCK GP
PULLEY GP
VALVE MECHANISM GP
CRANKSHAFT GP
MOUNTING GP-ENGINE


BASIC ENGINE

PISTON & ROD GP
 

#SEBP63520070
 

342-6646: PISTON & ROD GP

342-6646 PISTON & ROD GP
S/N MME1-UP
17.0:1 COMPRESSION RATIO
PART OF 347-0103, 528-7187 ENGINE AR-CORE
i03975512 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 524-5566 [1] PIN-PISTON  
2. 256-9658 [1] ROD AS-CONNECTING  
  160-8197 M [2] BOLT (M12X1.25X62-MM)  
3. 471-0275 [1] RING-PISTON (INTERMEDIATE)  
4. 262-2891 [1] RING-PISTON (OIL)  
5. 269-7290 [1] BEARING-CONNECTING ROD (STANDARD)  
  282-2478 AB BEARING-CONNECTING ROD (0.25-MM US)  
  282-2479 AB BEARING-CONNECTING ROD (0.51-MM US)  
6. 273-2600 [1] TUBE AS-OIL JET  
7. 300-1319 [1] RING-PISTON (TOP)  
8. 357-0447 [1] BODY AS-PISTON  
9. 6V-3940 M [1] BOLT (M8X1.25X25-MM)  
10. 6V-5589 [2] RING-RETAINING  
  A   NOT PART OF THIS GROUP
  B   USE AS REQUIRED
  M   METRIC PART
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP63520071
 

275-4260: PLUG GP-CYLINDER BLOCK

275-4260 PLUG GP-CYLINDER BLOCK
S/N MME1-UP
PROVIDES AN O-RING PORT PLUG FOR THE REAR OF THE BLOCK
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
FOR USE WITH ENGINES NOT USING A JACKET WATER HEATER
i03957089 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 398-5614 [1] PLUG AS  
  6V-5064 [1] SEAL-O-RING  
  360-3684 [1] PLUG  
 

#SEBP63520072
 

275-8699: PLUG GP-CYLINDER BLOCK

275-8699 PLUG GP-CYLINDER BLOCK
S/N MME1-UP
PROVIDES AN O-RING PORT PLUG FOR THE RH SIDE OF BLOCK
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
FOR USE WITH ENGINES NOT USING A BYPASS AUXILIARY COOLER
i03957091 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 398-5614 [1] PLUG AS  
  6V-5064 [1] SEAL-O-RING  
  360-3684 [1] PLUG  
 

#SEBP63520073
 

346-4997: PLUG GP-CYLINDER HEAD

346-4997 PLUG GP-CYLINDER HEAD
S/N MME1-UP
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
CANNOT BE USED WITH AIR COMPRESSOR GPS
i03951950 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 307-2671 [2] PLUG AS  
    (EACH INCLUDES)
  9S-8002 [1] PLUG (7/16-20-THD)  
  214-7566 [1] SEAL-O-RING  
2. 396-0404 [2] PLUG AS  
    (EACH INCLUDES)
  6V-3251 [1] SEAL-O-RING  
  360-3681 [1] PLUG (7/8-14-THD)  
3. 396-0405 [1] PLUG AS  
  6V-6609 [1] SEAL-O-RING  
  360-3680 [1] PLUG  
 

#SEBP63520074
 

292-9786: PLUG GP-ENGINE

292-9786 PLUG GP-ENGINE -COMPRESSION BRAKE
S/N MME1-UP
PROVIDES A PLUG GP FOR COMPRESSION BRAKE OIL SUPPLY WHEN COMPRESSION BRAKE IS NOT USED
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
i03957129 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6V-5683 M [1] BOLT (M6X1X16-MM)  
2. 4D-3088 [1] WASHER (0.266X0.438X0.19-IN THK)  
  M   METRIC PART
 

#SEBP63520075
 

342-7219: PULLEY GP-CRANKSHAFT

342-7219 PULLEY GP-CRANKSHAFT
S/N MME1-UP
PROVIDES SPUN STEEL 8-RIB K-SECTION POLY RIB CRANKSHAFT PULLEY AND ADAPTER
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
i03957150 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2W-7381 [1] PLATE-CLAMP  
2. 342-7220 [1] PULLEY (8-GROOVE)(8-GROOVE)  
3. 342-7221 [1] ADAPTER  
4. 8T-3666 M [4] BOLT (M14X2X60-MM)  
  M   METRIC PART
 

#SEBP63520076
 

263-0033: ROCKER ARM GP

263-0033 ROCKER ARM GP -INTAKE
S/N MME1-UP
PART OF 347-8760, 492-1194 VALVE MECHANISM GP
i03975657 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 260-7524 M [1] SCREW-VALVE ADJUSTMENT (M10X1.5-THD)  
2. 544-0524 [1] ROCKER ARM AS (INTAKE)  
3. 2Y-5829 M [1] NUT (M10X1.5-THD)  
  M   METRIC PART
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP63520077
 

347-8782: ROCKER ARM GP

347-8782 ROCKER ARM GP
S/N MME5037-UP
PART OF 492-1194 VALVE MECHANISM GP
i06545121 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 260-7524 M [1] SCREW-VALVE ADJUSTMENT (M10X1.5-THD)  
2. 347-8748 [1] ROCKER ARM AS (EXHAUST)  
3. 2Y-5829 M [1] NUT (M10X1.5-THD)  
  M   METRIC PART
  R   REMANUFACTURED PART MAY BE AVAILABLE
 

#SEBP63520078
 

295-2351: SEAL GP-CRANKSHAFT

295-2351 SEAL GP-CRANKSHAFT
S/N MME1-UP
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
i03951829 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4R-9999 [1] EXCLUDER-CRANKSHAFT SEAL  
2. 206-3719 M [9] BOLT AS  
3. 285-4074 [1] SEAL GP-CRANKSHAFT (REAR)  
  M   METRIC PART
 

#SEBP63520079
 

349-1172: SUPPORT GP-ENGINE

349-1172 SUPPORT GP-ENGINE
S/N MME1-UP
PART OF 382-4673, 395-0360 ENGINE AR-COMPLETE
i04037831 SEBP6352
  For full view, you need register

Parts for your 12M 2 MOTOR GRADER:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 349-1170 [1] SUPPORT GP-ENGINE  
1A. 349-1169 [1] SUPPORT-ENGINE  
1B. 6V-3535 [2] DOWEL  
2. 5P-8245 [2] WASHER-HARD (13.5X25.5X3-MM THK)  
3. 6V-5696 M [2] BOLT (M12X1.75X80-MM)  
4. 2M-0849 [4] WASHER-HARD (13.5X25.5X5-MM THK)  
5. 8T-0106 M [4] BOLT (M12X1.75X100-MM)  
  M   METRIC PART
 

Information:

Special Instruction
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
System Check after an NOx Reduction System (NRS) Cooler Failure for C9.3 through C18 Tier 4 Engines {1000, 1075, 108C, 108F}
System Check after an NOx Reduction System (NRS) Cooler Failure for C9.3 through C18 Tier 4 Engines {1000, 1075, 108C, 108F}
Piston Height Check Procedure for C9.3 through C18 Tier 4 Engines {1000, 108C, 1214}
Piston Height Check Procedure for C9.3 through C18 Tier 4 Engines {1000, 108C, 1214}
Technical Information Bulletin
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Tool Operating Manual
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
Reuse And Salvage Guidelines
Reuse and Salvage for Connecting Rods {1218}
Reuse and Salvage for Connecting Rods {1218}
Inspection Procedures and Specifications for Pistons and Piston Pins {1214, 1214}
Inspection Procedures and Specifications for Pistons and Piston Pins {1214, 1214}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
Testing and Adjusting
Excessive Bearing Wear - Inspect
C9.3 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Inspect
C9.3 Engines for Caterpillar Built Machines
Cylinder Liner Projection - Inspect
C9.3 Engines for Caterpillar Built Machines
Engine Crankcase Pressure (Blowby) - Test
C9.3 Engines for Caterpillar Built Machines
Piston Ring Groove - Inspect
C9.3 Engines for Caterpillar Built Machines
Disassembly and Assembly
Bearing Clearance - Check
C9.3
Engines for Caterpillar Built Machines

Piston Cooling Jets - Remove and Install
C9.3
Engines for Caterpillar Built Machines

Connecting Rod Bearings - Remove
C9.3
Engines for Caterpillar Built Machines

Connecting Rod Bearings - Install
C9.3
Engines for Caterpillar Built Machines

Pistons and Connecting Rods - Remove
C9.3
Engines for Caterpillar Built Machines

Pistons and Connecting Rods - Disassemble
C9.3
Engines for Caterpillar Built Machines

Pistons and Connecting Rods - Assemble
C9.3
Engines for Caterpillar Built Machines

Pistons and Connecting Rods - Install
C9.3
Engines for Caterpillar Built Machines

Caterpillar Parts SIS Catalog 12M 2 :

Truck sale:

 
181,000 
Caterpillar 12M2, Construction
- motor graders
YANCEY BROS. CO.
GA
 
187,500 
Caterpillar 12M2, Construction
- motor graders
YANCEY BROS. CO.
GA
 
289,000 
Caterpillar 12M2, Construction
- motor graders
WAGNER EQUIPMENT CO
 
170,000 
Caterpillar 12M2, Construction
- motor graders
YANCEY BROS. CO.
GA
205,000 
Caterpillar 12M2, Construction
- motor graders
CAROLINA CAT
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.