392-7834 MODULE GP-CONTROL -GENERATOR SET S/N JKK1-UP AN ATTACHMENT PMG3516 POWER MODULE

OPERATOR STATION

PANEL GP

0. 392-7834 MODULE GP-
1. 275-8193 MOUNTING G

SERVICE EQUIPMENT AND SUPPLIES

CHARTS & FILMS

2. 6L-4502 CHART-PLAT
3. 300-3728 FILM GP

GASKET & SEAL KITS

4. 353-5995 KIT-SEAL

PARTS GP-MISCELLANEOUS

5. 389-9653 PARTS GP-M
0. INFORMATION

POWER MODULE PMG3516 POWER MODULE JKK
PMG3516 Power Module JKK00001-UP POWERED BY G3516C Engine SEBP6665 PMG3516 JKK (2012)

OPERATOR STATION

PANEL GP

141-1956 CONTROL GP-ENGINE MONITORING

392-7830 MODULE GP-CONTROL

392-7833 MODULE GP-CONTROL

392-7834 MODULE GP-CONTROL

275-8193 MOUNTING GP-INSTRUMENT

#SEBP66650250

392-7834: MODULE GP-CONTROL

MODULE GP-CONTROL

392-7834 MODULE GP-CONTROL -GENERATOR SET
S/N JKK1-UP
AN ATTACHMENT

i05660129 SEBP6665

For full view, you need register

Parts for your PMG3516 POWER MODULE:

CATERPILLAR SIS

Part No	Qty	Parts name
392-8122	[1]	CONTROLLER (GENERATOR)
392-8125	[1]	MODULE (OPERATOR PANEL 1)
392-8127	[1]	MODULE (OPERATOR PANEL 2)

#SEBP66650251

275-8193: MOUNTING GP-INSTRUMENT

MOUNTING GP-INSTRUMENT

275-8193 MOUNTING GP-INSTRUMENT
S/N JKK1-UP
AN ATTACHMENT

i04894279 SEBP6665

2758193 MOUNTING GP-INSTRUMENT Parts scheme

For full view, you need register

Parts for your PMG3516 POWER MODULE:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	274-6154	[1]	BRACKET
2.	274-6155	[1]	BRACKET
3.	277-6857	[1]	BRACKET AS
	1F-0750	[8]	NUT-WELD (3/8-16-THD)
	8T-3490 M	[2]	NUT-WELD (M10X1.5-THD)
5.	320-9696	[1]	WIRE AS
7.	0S-1594	[10]	BOLT (3/8-16X1-IN)
9.	1B-9575	[5]	BOLT (5/16-18X1.56-IN)
11.	2B-2694	[1]	BOLT (5/16-18X2-IN)
12.	5M-2894	[10]	WASHER-HARD (10.2X18.5X2.5-MM THK)
13.	5P-8245	[4]	WASHER-HARD (13.5X25.5X3-MM THK)
14.	5S-0003	[6]	NUT (5/16-18-THD)
15.	6H-1717	[4]	BOLT (1/2-13X1.125-IN)
16.	9M-1974	[12]	WASHER-HARD (8.8X16X2-MM THK)
	M		METRIC PART

#SEBP66650252

6L-4502: CHART-PLATE & FILM

CHART-PLATE & FILM

6L-4502 CHART-PLATE & FILM
S/N JKK1-UP

i04921773 SEBP6665

For full view, you need register

Parts for your PMG3516 POWER MODULE:

CATERPILLAR SIS

Part No	Qty	Parts name
5P-1175	[1]	FILM-IDENTIFICATION (ENGINE OIL FILL)
		INSTALL ONE FILM ON THE TOP OF EACH OIL FILL CAP CENTERED BETWEEN THE HANDLE & THE TOP EDGE OF THE OIL FILL CAP.
250-3444	[1]	FILM-INFORMATION (STANDARD ROTATION)
		INSTALL FILM ON THE LH CAM GEAR COVER IN A VISIBLE LOCATION,
		IF THAT COVER IS NOT AVAILABLE MOVE TO THE RH CAM GEAR COVER.
	[1]	FILM-INFORMATION (EMISSION CONTROL)
		INSTALL FILM ON THE RH REAR VALVE COVER BASE,
		ALIGN WITH THE TOP EDGE OF THE TOP COVER & VISIBLE FROM THE SIDE OF THE ENGINE.
		IF THAT COVER IS NOT AVAILABLE MOVE FILM FORWARD TO THE FIRST AVAILABLE VALVE COVER BASE VISIBLE FROM THE SIDE.
225-3226	[2]	FILM-WARNING (HOT SURFACE)
		INSTALL FILMS ON CYL. #1 & #2 ON FRONT OF THE VALVE COVERS, ALIGN THE FILM WITH TOP EDGE OF THE VALVE COVER.
		IF THESE COVERS ARE NOT VISIBLE, MOVE FILM TO THE FIRST VISIBLE VALVE COVER.
225-3227	[2]	FILM-WARNING (HOT SURFACE)
		INSTALL ONE FILM ON THE RH SIDE ON THE OIL COOLER, ABOVE THE DIPSTICK, & ONE FILM ON THE LH SIDE OF THE ENGINE
		ON THE CRANKCASE COVER NEAR THE MIDLINE OF THE ENGINE. BOTH FILMS SHOULD BE VISIBLE FROM THE SIDE OF THE ENGINE.
228-3369	[2]	FILM-WARNING (DO NOT OPERATE, READ OMM)
		INSTALL ONE FILM ON CYLINDER'S #3 & #4 ON FRONT OF VALVE COVER, ALIGN THE FILM WITH TOP EDGE OF THE VALVE COVER.
		IF THESE COVERS ARE NOT VISIBLE, MOVE FILM TO THE FIRST VISIBLE VALVE COVER.
224-9830	[2]	FILM-WARNING (SHOCK HAZARD)
		INSTALL ONE FILM ON CYL. #11 & #12 ON FRONT OF THE VALVE COVERS,
		ALIGN THE FILM WITH THE TOP EDGE OF THE VALVE COVER.
		IF THESE COVERS ARE NOT VISIBLE, MOVE FILM TO THE FIRST VISIBLE VALVE COVER.
115-5852	[1]	PLATE & FILM GP (ENGINE INFORMATION)
		CONTACT YOUR LOCAL DEALER
		INSTALL FILM ON THE LH, FRONT, LOWER HEAD FACE OF THE BLOCK BETWEEN CYL #2 & THE FRONT HOUSING
		READABLE FROM THE REAR OF ENGINE.
		INSTALL CLEAR LAMINATE OVER FILM.
298-5631	[2]	PLATE-IDENTIFICATION (CAT)
		INSTALL ONE PLATE ON THE RH REAR & ONE PLATE ON THE LH FRONT OF THE HEAT SHIELD GUARDS,
		CENTERED FROM LEFT TO RIGHT & TOP TO BOTTOM ON THE VERTICAL SURFACE OF EACH GUARD,
		VISIBLE FROM THE SIDE OF THE ENGINE.
3N-3790	[1]	PLATE-SERIAL NUMBER (ENGINE)
		CONTACT YOUR LOCAL DEALER.
		REFLATTEN AFTER STAMPING.
		INSTALL ON LH SIDE OF BLOCK NEAR REAR FACE ON CAMSHAFT COMPARTMENT USING 7B-3028 DRIVE SCREWS.
		STAMP SERIAL NUMBER IN BLOCK JUST BELOW PLATE IN FIGURES 6 HIGH.
7B-3028	[2]	SCREW-DRIVE (NO 4X 3/16-IN)

#SEBP66650253

300-3728: FILM GP

FILM GP

300-3728 FILM GP
S/N JKK1-UP
AN ATTACHMENT

i05379871 SEBP6665

For full view, you need register

Parts for your PMG3516 POWER MODULE:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	225-4256 B	[2]	FILM-WARNING (HOT FLUID UNDER PRESSURE, U.S.)
2.	3E-6508	[1]	FILM-IDENTIFICATION (CAT)
3.	225-3227	[6]	FILM-WARNING (HOT SURFACE)
4.	3N-8591	[12]	FILM-INFORMATION (DO NOT LIFT)
5.	303-3440	[2]	FILM-IDENTIFICATION (CAT)
6.		[3]	FILM-WARNING (ELECTROCUTION HAZARD, READ OMM)
7.	424-6100	[1]	FILM-WARNING (ELECTROCUTION HAZARD, READ OMM)
8.	424-6101	[3]	FILM-WARNING (ELECTROCUTION HAZARD, READ OMM)
9.	134-7258 B	[2]	FILM-INFORMATION (EXTENDED LIFE COOLANT)
10.	225-3224	[3]	FILM-WARNING (AUTOMATIC ENGINE START)
11.	1P-2807	[4]	FILM-IDENTIFICATION (LIFT EYE LOCATION)
12.	225-3232	[2]	FILM-WARNING (FALLING OBJECT)
13.	144-0875	[1]	FILM-INFORMATION (OIL DRAIN)
14.	3N-9344	[2]	FILM-INFORMATION (CENTER OF GRAVITY)
15.	144-0876 B	[2]	FILM-INFORMATION (COOLANT DRAIN)
16.	142-7553 B	[2]	FILM-INFORMATION (ENGINE COOLANT FILL)
17.	142-7548 N	[2]	FILM-INFORMATION (POSITIVE, NEGATIVE)
18.	303-3428	[2]	FILM-IDENTIFICATION (CAT)
19.	460-8294 B	[2]	FILM-INFORMATION (LIFTING, READ OMM)(4-POINT)
20.	300-3756 B	[2]	FILM-INFORMATION (LIFTING, READ OMM)(3-POINT)
21.	300-3757 B	[2]	FILM-INFORMATION (LIFTING, READ OMM)(3-POINT)
22.	300-3758 B	[2]	FILM-INFORMATION (LIFTING, READ OMM)(3-POINT)
	B		USE AS REQUIRED
	N		NOT TO BE USED WITH AIR STARTER OPTION

#SEBP66650254

353-5995: KIT-SEAL

KIT-SEAL

353-5995 KIT-SEAL -SINGLE CYLINDER LINER
S/N XL61-UP
TO BE USED WITH ENGINES BUILT AFTER DEC 2009
FOR USE WITH REHS7402
FIELD INSTALLATION

i05927298 SEBP6665

For full view, you need register

Parts for your PMG3516 POWER MODULE:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8N-4707	[1]	BAND-FILLER
2.	352-6061	[1]	SEAL-LINER
3.	7N-2046	[3]	SEAL-O-RING

			FOR A LIST OF RELATED PARTS THAT MAY BE REQUIRED FOR THE ENGINE REBUILD TO THE KIT CONSIST, PLEASE VISIT

			HTTP://DEALER.CAT.COM/RELATED

#SEBP66650255

389-9653: PARTS GP-MISCELLANEOUS

PARTS GP-MISCELLANEOUS

389-9653 PARTS GP-MISCELLANEOUS
S/N JKK1-UP
AN ATTACHMENT

i06805479 SEBP6665

For full view, you need register

Parts for your PMG3516 POWER MODULE:

CATERPILLAR SIS

Part No	Qty	Parts name
206-0884 Y	[2]	AIR CLEANER GP (SINGLE ELEMENT)
215-2882 Y	[16]	MOUNTING GP-POWER MODULE
		-OR-
486-4254 Y	[16]	MOUNTING GP-VIBRATION ISOLATOR
286-0177	[1]	BATTERY CHARGER
8T-4988	[4]	CLAMP-HOSE
8T-4990	[4]	CLAMP-HOSE
135-5294	[2]	ELBOW-RUBBER
320-2785	[2]	HOSE-REDUCER
Y		SEPARATE ILLUSTRATION