2298951 SENDER AS-FUEL LEVEL Caterpillar parts
CB-214E
Rating:
Alternative (cross code) number:
CA2298951
229-8951
2298951
CA2298951
229-8951
2298951
Weight: 0.46 pounds 0 kg.
VIBRATORY COMPACTOR,
Compatible equipment models: 2298951:
Number on catalog scheme:
3
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ 6V-9509 Face Seal Plug 2
6V-9830 Cap As 2 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Remove the main hydraulic pump. Refer to Disassembly and Assembly, "Main Hydraulic Pump - Remove".Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN THE PHOTOGRAPHS IN THE INSTALLATION OR IN THE REMOVAL. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.Note: The following procedure should be used for the pump controls on both sides of the main hydraulic pump.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the oil from the hydraulic tank into a suitable container for storage or for disposal. The capacity of the hydraulic tank is approximately150 L (40 US gal).
Open the right, rear door for the pump compartment.
Illustration 1 g00805073
Right side
Disconnect harness assembly (1). Remove bolt (2) that secures the clip and the harness assembly.
Disconnect hose assembly (3) .
Illustration 2 g00805069
Remove bolts (4) and remove pump control (5) .
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ 6V-9509 Face Seal Plug 2
6V-9830 Cap As 2 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Remove the main hydraulic pump. Refer to Disassembly and Assembly, "Main Hydraulic Pump - Remove".Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN THE PHOTOGRAPHS IN THE INSTALLATION OR IN THE REMOVAL. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.Note: The following procedure should be used for the pump controls on both sides of the main hydraulic pump.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components.To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly.Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Drain the oil from the hydraulic tank into a suitable container for storage or for disposal. The capacity of the hydraulic tank is approximately150 L (40 US gal).
Open the right, rear door for the pump compartment.
Illustration 1 g00805073
Right side
Disconnect harness assembly (1). Remove bolt (2) that secures the clip and the harness assembly.
Disconnect hose assembly (3) .
Illustration 2 g00805069
Remove bolts (4) and remove pump control (5) .
Caterpillar parts catalog:
Parts sender Caterpillar catalog:
2395812
SENDER AS-FUEL LEVEL
CP-533E, CS-533E, CS-54
CP-533E, CS-533E, CS-54
CS-533E
CP-573E, CP-663E, CS-563E, CS-583E, CS-663E, CS-683E
CP-573E, CP-663E, CS-563E, CS-583E, CS-663E, CS-683E
1963830
SENDER GP-FUEL LEVEL
AP-655C
AP-655C
1943425
SENDER AS-FUEL LEVEL
CB-434D, CS-323C
CB-434D, CS-323C
2720021
SENDER AS-FUEL LEVEL
CD-54B, CP-56, CP-64, CP-76, CS-56, CS-64, CS-74
CD-54B, CP-56, CP-64, CP-76, CS-56, CS-64, CS-74
2741472
SENDER-FUEL LEVEL
AP-600D, AP-655D, BG600D, BG655D
AP-600D, AP-655D, BG600D, BG655D
2592024
SENDER-PRESSURE
PM-200
PM-200
2638420
SENDER AS-FUEL LEVEL
AP-1055D, BG-2455D, BG-260D
AP-1055D, BG-2455D, BG-260D
3253231
SENDER AS-FUEL LEVEL
RM-300, RM-500
RM-300, RM-500
2396918
SENDER AS-FUEL LEVEL
RM-300, RM-500
RM-300, RM-500