1744082 SENSOR & MTG GP-LIFT POSITION Caterpillar parts
980G II, 980H
Rating:
Alternative (cross code) number:
CA1744082
174-4082
1744082
CA1744082
174-4082
1744082
WHEEL LOADER,
Information:
start by:a) remove oil pan1. The main bearing caps are installed with the part number toward the front of the engine. Each cap has a number on the bottom of the cap which is the same as the number on the camshaft side of the cylinder block. 2. Remove the bolts that hold main cap (1). Remove bearing cap (1) and the lower half of the main bearing.3. Remove the bearing from the cap. 4. Turn the crankshaft until tool (A) can be installed in the oil hole in the crankshaft journal. Install tool (A). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
5. Install lower bearings in the bearing caps.6. Install upper bearings in the cylinder block with tool (A). Be sure the tab on the back of the bearings fits in the groove of the caps and cylinder block.
When bearing caps are installed, make sure the caps are installed with the part number toward the front of the engine and the number on the bottom of the cap is the same as the number on the camshaft side of the engine.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn crankshaft when Plastigage is in position to check clearance.7. Check the bearing clearance with tool (B) as follows: a) Put tool (B) and cap (1) in position and install the bolts. Tighten the bolts to a torque of 120 10 lb.ft. (160 14 N m).b) Remove the bearing cap and measure the thickness of the Plastigage. The main bearing clearance must be .0030 to .0066 in. (0.076 to 0.168 mm). The maximum permissible clearance is .010 in. (0.25 mm). 8. Put clean engine oil on the bolt threads and lower half of the main bearing. Put bearing cap (1) and lower half of main bearing (2) in position on the engine. Install the bolts. Tighten the bolts to a torque of 120 10 lb.ft. (160 14 N m).9. Do Steps 1 through 9 for the remainder of the bearings. When a replacement of the thrust plates on
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
5. Install lower bearings in the bearing caps.6. Install upper bearings in the cylinder block with tool (A). Be sure the tab on the back of the bearings fits in the groove of the caps and cylinder block.
When bearing caps are installed, make sure the caps are installed with the part number toward the front of the engine and the number on the bottom of the cap is the same as the number on the camshaft side of the engine.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn crankshaft when Plastigage is in position to check clearance.7. Check the bearing clearance with tool (B) as follows: a) Put tool (B) and cap (1) in position and install the bolts. Tighten the bolts to a torque of 120 10 lb.ft. (160 14 N m).b) Remove the bearing cap and measure the thickness of the Plastigage. The main bearing clearance must be .0030 to .0066 in. (0.076 to 0.168 mm). The maximum permissible clearance is .010 in. (0.25 mm). 8. Put clean engine oil on the bolt threads and lower half of the main bearing. Put bearing cap (1) and lower half of main bearing (2) in position on the engine. Install the bolts. Tighten the bolts to a torque of 120 10 lb.ft. (160 14 N m).9. Do Steps 1 through 9 for the remainder of the bearings. When a replacement of the thrust plates on
Caterpillar SIS machinery equipment:
Caterpillar SIS
980G II Wheel Loader AWH00001-UP (MACHINE) POWERED BY 3406 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980G II Wheel Loader AXG00001-UP (MACHINE) POWERED BY 3406E Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980H Wheel Loader KZL00001-UP (MACHINE) POWERED BY C15 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine »
174-4082
SENSOR & MTG GP-LIFT POSITION
980G SERIES II WHEEL LOADER AYT00001-UP (MACHINE) POWERED BY 3406E »
174-4082
SENSOR AND MOUNTING GROUP
980H WHEEL LOADER A8J00001-03999 (MACHINE) POWERED BY C15 ENGINE »
174-4082
LIFT SENSOR AND MOUNTING GROUP
980H WHEEL LOADER A8J04000-UP (MACHINE) POWERED BY C15 ENGINE »
174-4082
SENSOR AND MOUNTING GROUP
Caterpillar parts catalog:
Parts sensor Caterpillar catalog:
2566453
SENSOR-TEMPERATURE
120K, 120K 2, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2491, 24M, 2570C, 259...
120K, 120K 2, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2491, 24M, 2570C, 259...
1946725
SENSOR GP-PRESSURE
120H, 135H, 140G, 140H, 140M, 14M, 160H, 16M, 24H, 24M, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D...
120H, 135H, 140G, 140H, 140M, 14M, 160H, 16M, 24H, 24M, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D...
1895746
SENSOR GP-SPEED
120H, 120H ES, 120H NA, 12H ES, 12H NA, 135H, 135H NA, 140H ES, 140H NA, 143H, 160H ES, 160H NA, 163H NA, 3114, 3116, 3126, 3126B, 312C, 315C, 320B, 322B, 322B LN, 322C, 322C FM, 325B, 325B L, 325C, 3...
120H, 120H ES, 120H NA, 12H ES, 12H NA, 135H, 135H NA, 140H ES, 140H NA, 143H, 160H ES, 160H NA, 163H NA, 3114, 3116, 3126, 3126B, 312C, 315C, 320B, 322B, 322B LN, 322C, 322C FM, 325B, 325B L, 325C, 3...
2016617
SENSOR GP-SPEED
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 583T, 587T, 621B, 621G, 621H, 623G, 623H, 627F, 627G, 627H, 631D, 631E, 631G, 633E II, 6...
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 583T, 587T, 621B, 621G, 621H, 623G, 623H, 627F, 627G, 627H, 631D, 631E, 631G, 633E II, 6...
1309811
SENSOR GP-TEMPERATURE
120H, 12H, 140H, 140M, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 236B, 267B, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L...
120H, 12H, 140H, 140M, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 236B, 267B, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L...
6V2455
SENSOR GP-SPEED
312B L, 315B L, 322B L, 325B L, 330, 3304, 3304B, 3306, 3306B, 330B, 330B L, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 3456, 345B, 345B II, 345B II MH, 345B L, 3508, 3508B, 3508C, 3512, 3512B, 35...
312B L, 315B L, 322B L, 325B L, 330, 3304, 3304B, 3306, 3306B, 330B, 330B L, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 3456, 345B, 345B II, 345B II MH, 345B L, 3508, 3508B, 3508C, 3512, 3512B, 35...
2644297
SENSOR AS-TEMPERATURE
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD...
120H, 120K, 120K 2, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD...
1887513
SENSOR GP-SPEED
3406E, 735, 740, 824C, 824G, 824G II, 825G II, 826G II, 834G, 836G, 980G, 980G II, 988G, AD30, C-15, C-16, C18, MTC835, R2900G
3406E, 735, 740, 824C, 824G, 824G II, 825G II, 826G II, 834G, 836G, 980G, 980G II, 988G, AD30, C-15, C-16, C18, MTC835, R2900G
1945341
SENSOR GP-SPEED
980G II, C-15, C-16, C-18, C16, C18, MTC835
980G II, C-15, C-16, C-18, C16, C18, MTC835
1918304
SENSOR GP-SPEED
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 420E, 420F, 428E, 428F, 430E, 430F, 432...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 420E, 420F, 428E, 428F, 430E, 430F, 432...
2746719
SENSOR GP-PRESSURE
120K, 120K 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 2864C, 324D, 324D ...
120K, 120K 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 2864C, 324D, 324D ...
2746717
SENSOR-PRESSURE
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 36...
120K, 120K 2, 120M, 12K, 12M, 140G, 140K, 140K 2, 140M, 14M, 160K, 160M, 16M, 24M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 36...
3944737
SENSOR GP-SPEED
3512, 3512B, 3512C, 3516, 3516B, G3516
3512, 3512B, 3512C, 3516, 3516B, G3516
4158044
SENSOR GP-PRESSURE
349F L, 374F L, 390F L, 621K, 623K, 627K, 725C, 730C, 770G, 770G OEM, C9.3, D8T, D9T
349F L, 374F L, 390F L, 621K, 623K, 627K, 725C, 730C, 770G, 770G OEM, C9.3, D8T, D9T
2940112
SENSOR GP-POSITION
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E, BG600D, BG655D
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E, BG600D, BG655D
3010071
SENSOR GP-POSITION
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E
AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG1000E, BG1055E, BG500E
1687855
SENSOR GP-FEEDER
AP-1000B, AP-1055B, AP-650B, BG-225C, BG-2455C, BG-245C
AP-1000B, AP-1055B, AP-650B, BG-225C, BG-2455C, BG-245C
3469686
SENSOR GP-ENGINE
773G, 773G OEM, 775G, 775G OEM, 777G, 844K, 990K
773G, 773G OEM, 775G, 775G OEM, 777G, 844K, 990K
2123421
SENSOR GP-PRESSURE
3508B, 3512, 3512B, 3516, 3516B
3508B, 3512, 3512B, 3516, 3516B
2497806
SENSOR AR-GRADE
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H
1053769
SENSOR GP-POSITION
143H, 163H NA, 785C, 789C, 938F, 938G, 950G, AP-1000B, IT38F, IT38G, PM-465
143H, 163H NA, 785C, 789C, 938F, 938G, 950G, AP-1000B, IT38F, IT38G, PM-465
2725451
SENSOR GP-SONIC
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H
3855863
SENSOR & MTG GP-PRESSURE
2670C, 573C, C7.1
2670C, 573C, C7.1