SENSOR GP-SOOT 4644913 - Caterpillar

4644913 SENSOR GP-SOOT Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4644913
464-4913
4644913

Weight: 0.99 pounds 0 kg.

Buy SENSOR GP-SOOT 4644913 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:

4644913 MONITOR GP-EXH 20R7476 R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Ochoos RNA4913 Heavy Duty Needle Roller Bearing Entity Needle Bearing Without Inner Ring 4644913 Size 729025

$32.29

01 Jun 2021

RU: Udith

Ochoos RNA4913 Heavy Duty Needle Roller Bearing Entity Needle Bearing Without Inner Ring 4644913 Size 729025
Ochoos Material: Steel || Model number: RNA4913 || Coatings: other || Structure: other

This part in 2 request: Show. This information for suppliers only!

#963207 4644913

2022-09-04

#641882 4644913

2021-04-27

Number on catalog scheme: 2

Caterpillar 4644913 Parts scheme SENSOR GP-SOOT

For full view, you need register

Information:

Removal Procedure
Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Support the engine.
Install a suitable lifting device to the flywheel housing. Support the weight of the housing. The weight of the flywheel housing is approximately 30 kg (66 lb).
Illustration 1 g01326591
Illustration 2 g01305649
Typical example
Remove bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
Remove bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block.
Remove bolts (1) that fasten back plate (2) to flywheel housing (8).
Remove nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
Carefully remove flywheel housing (8) from back plate (2) and dowels (7). Use a suitable lifting device to remove the flywheel housing. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the mating surfaces of back plate (2) and flywheel housing (8) are clean and free from damage. Inspect the crankshaft rear seal (not shown) for leaks. If necessary, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure. Inspect dowels (7) for damage. If the dowels are damaged, use new parts for replacement.
Illustration 3 g01305649
Illustration 4 g01326591
Typical example
Use a suitable lifting device to align flywheel housing (8) to dowels (7). The weight of the flywheel housing is approximately 30 kg (66 lb). Install the flywheel housing to the back plate.
Install nuts (5) and the bolts (not shown) that fasten back plate (2) to flywheel housing (8).
Install bolts (1) that fasten back plate (2) to flywheel housing (8).
Install bolts (6) on each side of the cylinder block. These bolts fasten flywheel housing (8) to the cylinder block.
Remove the lifting device from the flywheel housing.
Install bolts (3) and (4) that fasten flywheel housing (8) to the cylinder block.
Tighten the fasteners to a torque of 25 N m (19 lb ft). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".