AVSPARE.COM
parts catalog

SENSOR AS-TEMPERATURE 4656888 - Caterpillar


4656888 SENSOR AS-TEMPERATURE Caterpillar parts
Rating:
26
Alternative (cross code) number:
CA4656888
465-6888
4656888
Caterpillar 4656888 SENSOR AS-TEMPERATURE
Weight: 0.12 pounds 0 kg.

Buy SENSOR AS-TEMPERATURE 4656888 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 7
  For full view, you need register

Information:


Diesel engine exhaust contains products of combustion which may cause personal injury.Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside.
Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts.Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified.The machine must be parked on a level surface and the engine stopped.Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine.
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Drive the machine to a smooth, horizontal surface.
Illustration 1 g02599236
Move propel lever (1) to the NEUTRAL position.
Rotate speed dial (4) to the MINIMUM position.
Move parking brake switch (2) to the ON position.
Move travel mode switch (3) to the PAVE position.Note: The machine must be in PAVE mode in order to operate the screed lift system, the hopper system, the apron system, and the auger lift system.
Illustration 2 g02599237
Move screed lift switch (5) to the FLOAT position. Allow the screed to lower to the ground.Note: The screed lift switch on the inactive operator station must also be in the FLOAT position in order to lower the screed.
After the screed rests on the ground, move screed lift switch (5) to the HOLD position.
Illustration 3 g02599238
Move throttle control switch (6) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
Illustration 4 g02599239
Move engine start switch (7) to the OFF position.
Illustration 5 g02599240
Open access door (8) on the left side of the machine.
Illustration 6 g02599241
Measure the deflection along rear edge of chain (9), at the midpoint of the chain. Record the reading, measure the deflection along the front edge of the chain at the midpoint of the chain. Add the two measurements.
Deflection of chain (9) should be less than 6.4 mm (0.25 inch).
If deflection of chain (9) is outside the specified range, adjust the chain tension with the following procedure.
Illustration 7 g02599242
Loosen, but do not remove, three bolts (10) .
Illustration 8 g02599243
Loosen lock nut (13) .
Hold bolt (11), and turn adjustment nut (12) until deflection of chain (9) is within the specified range.
Tighten lock nut (13) .
Tighten mounting bolts (10) .
Close left access door (8) .

Caterpillar parts catalog:

Caterpillar parts catalog
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
272D2 & 272D2 XHP Skid Steer Loader BL200001-UP (MACHINE) POWERED BY C3.8 Engine
299D2 XHP & 299D2 Compact Track Loader DX200001-UP (MACHINE) POWERED BY C3.8 Engine
297D2 & 297D2 XHP Multi Terrain Loader BL700001-UP (MACHINE) POWERED BY C3.8 Engine
272D3 XHP, 272D3 Skid Steer Loader GJ200001-UP (MACHINE) POWERED BY C3.8 Engine
299D3, 299D3 XHP Compact Track Loader AN900001-UP (MACHINE) POWERED BY C3.8 Engine
299D3 XE Compact Track Loader LB300001-UP (MACHINE) POWERED BY C3.8 Engine
299D2 XHP & 299D2 Compact Track Loader DX200001-UP (MACHINE) POWERED BY C3.8 Engine


Parts sensor Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.