SENSOR AS-SPEED 4921070 - Caterpillar

4921070 SENSOR AS-SPEED Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4921070
492-1070
4921070

Buy SENSOR AS-SPEED 4921070 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

49210-70 - Tubing, PTFE All Natural 1.70mm (.07) ID x 2.0mm OD. Low Pressure, Translucent, 5 Meter roll - TUBING PTFE 2MM OD X 1.7MM ID - Each

$48.98

28 Jun 2022

US: All Star Suppli

49210-70 - Tubing, PTFE All Natural 1.70mm (.07) ID x 2.0mm OD. Low Pressure, Translucent, 5 Meter roll - TUBING PTFE 2MM OD X 1.7MM ID - Each
MicroSolv Technology Corp Description : TUBING PTFE 2MM OD X 1.7MM ID || Supplier No : 49210-70 || Unit : Each

This part in 1 request: Show. This information for suppliers only!

#718912 4921070

2021-09-15

Number on catalog scheme: 9

Caterpillar 4921070 Parts scheme SENSOR AS-SPEED

For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to the appropriate piston cooling jet.
Illustration 1 g01265615
Typical example
Remove bolt (1) and piston cooling jet (2) from the cylinder block.
Repeat Step 1 and Step 2 for the remaining piston cooling jets. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01265615
Clean the piston cooling jets and inspect the piston cooling jets for damage. Ensure that the valve is free to move within each piston cooling jet. Replace any damaged piston cooling jets.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to access the mounting flange for the piston cooling jet.
Position piston cooling jet (2) in the cylinder block. Install bolt (1). Tighten the bolt to a torque of 9 N m (80 lb in).
Repeat Step 2 and Step 3 for the remaining piston cooling jets.
If the cylinder head has been removed, It is possible to check the alignment of the piston cooling jets. Refer to Specifications, "Piston Cooling Jet Alignment" for more information. Note: It is not possible to check the alignment of the piston cooling jets with the cylinder head in position.End By:
If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and Assembly, "Balancer - Install". If the engine is not equipped with a balancer, install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".