2262886 SERVICE GROUP Caterpillar parts
572R II, D6R II, D7R II, D8R II
Rating:
Alternative (cross code) number:
CA2262886
226-2886
2262886
CA2262886
226-2886
2262886
PIPELAYER, TRACK-TYPE TRACTOR,
Compatible equipment models: 2262886:
Information:
Assembly Procedure
Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause problems in the future. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g03230839
(1) Rectifier (2) Stator
Connect and solder the stator leads to the positive (+) diodes of rectifier (1) .
Illustration 2 g03230840
(1) Rectifier (2) Stator (3) Position wave washer
Position the insulators on the rectifier terminal studs. Position rectifier (1), and stator (2) into the rear frame, and install the three screws. Install the terminal insulators, washers, and nuts. Position wave washer (3) into the bearing bore of the rear frame.
Illustration 3 g03230842
(4) Rear bearing (5) Slip ring
Install slip ring (5) on the rotor. Connect and solder the rotor leads to the slip ring (5). Install rear bearing (4) .
Illustration 4 g03230845
(6) Bearing cover (7) Spacer (8) Front bearing
Install bearing cover (6), front bearing (8), and spacer (7) on the rotor.
Illustration 5 g03230846
(9) Rotor
Install rotor (9) and the four screws into the front frame.
Illustration 6 g03230848
(10) Stator assembly (11) Rotor assembly
Assemble front frame and rotor assembly (11) into rear frame and stator assembly (10). Make sure that the wave washer is fixed in the rear frame bearing bore. Align the front and rear frame marks made at disassembly for correct assembly. Install the four screws.
Illustration 7 g03230896
(12) Pulley (13) Fan
Install the key, fan (13), pulley (12), washer, and pulley nut. Tighten the nut to a torque of: 3E-7295 Charging Alternator Gp, and 9X-0341 Charging Alternator Gp ... 70 5 N m (52 4 lb ft) 8C-5535 Charging Alternator Gp, 7T-2876 Charging Alternator Gp, 2Y-4212 Charging Alternator Gp, and 2Y-8310 Charging Alternator Gp ... 35 10 N m (26 7 lb ft) 9W-3043 Charging Alternator Gp ... 50 5 N m (37 4 lb ft)
Illustration 8 g03230899
(14) Capacitor lead (15) Regulator
Install the capacitor and connect capacitor lead (14) to the back of the alternator.
Install regulator (15) .End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause problems in the future. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g03230839
(1) Rectifier (2) Stator
Connect and solder the stator leads to the positive (+) diodes of rectifier (1) .
Illustration 2 g03230840
(1) Rectifier (2) Stator (3) Position wave washer
Position the insulators on the rectifier terminal studs. Position rectifier (1), and stator (2) into the rear frame, and install the three screws. Install the terminal insulators, washers, and nuts. Position wave washer (3) into the bearing bore of the rear frame.
Illustration 3 g03230842
(4) Rear bearing (5) Slip ring
Install slip ring (5) on the rotor. Connect and solder the rotor leads to the slip ring (5). Install rear bearing (4) .
Illustration 4 g03230845
(6) Bearing cover (7) Spacer (8) Front bearing
Install bearing cover (6), front bearing (8), and spacer (7) on the rotor.
Illustration 5 g03230846
(9) Rotor
Install rotor (9) and the four screws into the front frame.
Illustration 6 g03230848
(10) Stator assembly (11) Rotor assembly
Assemble front frame and rotor assembly (11) into rear frame and stator assembly (10). Make sure that the wave washer is fixed in the rear frame bearing bore. Align the front and rear frame marks made at disassembly for correct assembly. Install the four screws.
Illustration 7 g03230896
(12) Pulley (13) Fan
Install the key, fan (13), pulley (12), washer, and pulley nut. Tighten the nut to a torque of: 3E-7295 Charging Alternator Gp, and 9X-0341 Charging Alternator Gp ... 70 5 N m (52 4 lb ft) 8C-5535 Charging Alternator Gp, 7T-2876 Charging Alternator Gp, 2Y-4212 Charging Alternator Gp, and 2Y-8310 Charging Alternator Gp ... 35 10 N m (26 7 lb ft) 9W-3043 Charging Alternator Gp ... 50 5 N m (37 4 lb ft)
Illustration 8 g03230899
(14) Capacitor lead (15) Regulator
Install the capacitor and connect capacitor lead (14) to the back of the alternator.
Install regulator (15) .End By: Install the alternator on the machine. Refer to Disassembly and Assembly, "Alternator - Install" for the machine that is being serviced.
Caterpillar SIS machinery equipment:
Caterpillar SIS
D7R SERIES II TRACK-TYPE TRACTOR /FINGER TIP CONTROL/ BNM00001-UP (MACHINE) POWERED BY 3176C ENGINE »
226-2886
SERVICE GROUP
D7R SERIES II TRACK-TYPE TRACTOR /DIFFERENTIAL STEERIN/ BNX00001-00900 (MACHINE) POWERED BY 3176C ENGINE »
226-2886
SERVICE GROUP
D6R SERIES II TRACK-TYPE TRACTOR DS STD BNL00501-UP (MACHINE) POWERED BY C9 ENGINE »
226-2886
SERVICE GROUP
D6R SERIES II TRACK-TYPE TRACTOR DS XL BRZ00501-UP (MACHINE) POWERED BY C-9 ENGINE »
226-2886
SERVICE GROUP
D6R SERIES II TRACK-TYPE TRACTOR FTC STD BMK00501-UP (MACHINE) POWERED BY C-9 ENGINE »
226-2886
SERVICE GROUP
D6R SERIES II TRACK-TYPE TRACTOR FTC XL BPS00501-UP (MACHINE) POWERED BY C-9 ENGINE »
226-2886
SERVICE GROUP
D6R SERIES II TRACK-TYPE TRACTOR DS XW BRE00501-UP (MACHINE) POWERED BY C-9 ENGINE »
226-2886
SERVICE GROUP
Caterpillar parts catalog:
Parts service Caterpillar catalog:
3339327
SERVICE GROUP
D6R III, D7R II
D6R III, D7R II
2350669
SERVICE CENTER GP
D7R II
D7R II
1949351
SERVICE GP-MACHINE
933C, 939C, D4C III, D5C III, D8R II
933C, 939C, D4C III, D5C III, D8R II
2525628
SERVICE GROUP
D6R II, D7R II
D6R II, D7R II
3231272
SERVICE GROUP
572R II, D6R III, D6T, D7R II
572R II, D6R III, D6T, D7R II
2707832
SERVICE GP-IMPLEMENT
D6R II
D6R II
2621614
SERVICE GP-POWER TRAIN
D6R II, D7R II, D8R II
D6R II, D7R II, D8R II
3352383
SERVICE GP-IMPLEMENT
120H, 120K, 12H, 12K, 135H, 140H, 140K, 143H, 14H, 160H, 160K, 163H, 16H, D6R II, D7R II
120H, 120K, 12H, 12K, 135H, 140H, 140K, 143H, 14H, 160H, 160K, 163H, 16H, D6R II, D7R II
3340372
SERVICE GP-POWER TRAIN
572R II, 583T, 587T
572R II, 583T, 587T
2688747
SERVICE GP-POWER TRAIN
572R II
572R II
3262816
SERVICE GP-MONITOR
3412E, C12, C18, C32, C7, C9
3412E, C12, C18, C32, C7, C9
3N4181
SERVICE GP
D379, D398, D399, G379, G398, G399
D379, D398, D399, G379, G398, G399
9S7993
SERVICE METER
627, 637, 814, 815, 816, 920, 930, 950, 951B, 955K, 955L, 966C, 980B, D4D, D5, D6C, D7F, D7G
627, 637, 814, 815, 816, 920, 930, 950, 951B, 955K, 955L, 966C, 980B, D4D, D5, D6C, D7F, D7G
7N4543
SERVICE HORN GROUP
768B, 769, 772, 773
768B, 769, 772, 773
3863458
SERVICE GP-MONITOR
312D, 312D2, 312D2 GC, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 320D, 320D FM, 320D GC, 320D2, 323D L, 324D, 324D L, 324D LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 330D, 330D L, 330D LN...
312D, 312D2, 312D2 GC, 313D, 313D2, 313D2 LGP, 315D L, 318D L, 318D2 L, 320D, 320D FM, 320D GC, 320D2, 323D L, 324D, 324D L, 324D LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 330D, 330D L, 330D LN...
1872033
SERVICE AR-DIFF & BEVEL GEAR
797, 797B
797, 797B
3092288
SERVICE GP-FILTER
AD55B, AD60
AD55B, AD60
2377351
SERVICE GP-POWER TRAIN
953C, 963C, 973C
953C, 963C, 973C