1004027 SHAFT-FAN Caterpillar parts
3116, 3126, 3126B, 3126E
Rating:
Alternative (cross code) number:
CA1004027
100-4027
1004027
CA1004027
100-4027
1004027
Weight: 3 pounds 1 kg.
TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Belt - Baler Upper fits New Holland 650 654 658 660 664 fits Case IH RBX562 RBX563 1004027
Parts ASAP Compatible with Case IH Baler(s) RBX562 (requires 8), RBX563 (requires 8) || Compatible with New Holland Baler(s) 650, 654, 658, 660, 664 || Replaces Mfg Number(s) 1004027 || 7" X 420.5" || 3 Ply Mini Rough top with Heavy Plate
Parts ASAP Compatible with Case IH Baler(s) RBX562 (requires 8), RBX563 (requires 8) || Compatible with New Holland Baler(s) 650, 654, 658, 660, 664 || Replaces Mfg Number(s) 1004027 || 7" X 420.5" || 3 Ply Mini Rough top with Heavy Plate
Whatman 1004-027 Quantitative Filter Paper Circles, 20-25 Micron, 3.7 s/100mL/sq inch Flow Rate, Grade 4, 27mm Diameter (Pack of 400)
Whatman 2.7cm || Grade 4 || Used in qualitative analytical techniques to determine and identify materials || Extremely fast filtering; provides excellent retention of coarse particles (20-25µm) and gelatinous precipitates such as ferric hydroxide and aluminium hydroxide || Used when high flow rates in air pollution monitoring are required and the collection of fine particles is not critical
Whatman 2.7cm || Grade 4 || Used in qualitative analytical techniques to determine and identify materials || Extremely fast filtering; provides excellent retention of coarse particles (20-25µm) and gelatinous precipitates such as ferric hydroxide and aluminium hydroxide || Used when high flow rates in air pollution monitoring are required and the collection of fine particles is not critical
$69.46
30 Jun 2021
US: All Star Suppli
Whatman 1004-027 Quantitative Filter Paper Circles, 20-25 Micron, 3.7 s/100mL/sq inch Flow Rate, Grade 4, 27mm Diameter (Pack of 400)
Whatman 2.7cm || Grade 4 || Used in qualitative analytical techniques to determine and identify materials || Extremely fast filtering; provides excellent retention of coarse particles (20-25µm) and gelatinous precipitates such as ferric hydroxide and aluminium hydroxide || Used when high flow rates in air pollution monitoring are required and the collection of fine particles is not critical
Whatman 2.7cm || Grade 4 || Used in qualitative analytical techniques to determine and identify materials || Extremely fast filtering; provides excellent retention of coarse particles (20-25µm) and gelatinous precipitates such as ferric hydroxide and aluminium hydroxide || Used when high flow rates in air pollution monitoring are required and the collection of fine particles is not critical
Number on catalog scheme:
6
For full view, you need register
Information:
Troubleshooting
If the engine is run when there is a problem (malfunction) with the EGR system, be sure to drain the oil from the engine after the problem (malfunction) has been corrected. Install new oil filters and put new oil in the engine.
EGR Systems
Fuel Setting
5P6577 Fuel Setting Tool Group8S4627 Circuit TesterThe procedure that follows, for fuel setting can be done with the housing for the fuel injection pumps either on or off the engine.
Before doing any service work on this fuel system, the outside of the housing for the fuel injection pumps and all parts connected to it must be especially clean.
1. Remove EGR switch cover (1).
REMOVAL OF EGR SWITCH COVER
1. EGR switch cover.2. Install 5P298 Pin (4) in hole. The pin length in mm is given on the large diameter of the pin. Put spring (3) on pin (4) and install 5P6602 Adapter (2).
INSTALLATION OF ADAPTER
2. 5P6602 Adapter. 3. 3J6956 Spring. 4. 5P298 Zero Set Pin (with 17.8507 on it).3. Install 8S7271 Set Screw (6). Remove shut-off solenoid (5).
INSTALLATION OF SET SCREW
5. Solenoid. 6. 8S7271 Set Screw.4. Use wrench (7) and tighten set screw (6) until pin is against pump housing. Install collet clamp (11) in adapter (2). Install indicator (9) and point in collet clamp (11). Loosen nut (10). Move governor control lever (12) to full load position. Make an adjustment to the indicator (move indicator up or down) until both hands are at zero. Tighten nut (10) of the collet clamp. To make a fine adjustment to indicator (9), loosen lock (8). Turn bezel until large hand is on zero and tighten lock (8). Remove set screw (6) with wrench (7).
ADJUSTMENT OF DIAL INDICATOR
2. 5P6602 Adapter. 7. Wrench. 8. Lock. 9. Indicator. 10. Nut. 11. Collet clamp. 12. Governor control lever.5. Release governor control lever (12) and move it to low idle position. Connect the wire clip
If the engine is run when there is a problem (malfunction) with the EGR system, be sure to drain the oil from the engine after the problem (malfunction) has been corrected. Install new oil filters and put new oil in the engine.
EGR Systems
Fuel Setting
5P6577 Fuel Setting Tool Group8S4627 Circuit TesterThe procedure that follows, for fuel setting can be done with the housing for the fuel injection pumps either on or off the engine.
Before doing any service work on this fuel system, the outside of the housing for the fuel injection pumps and all parts connected to it must be especially clean.
1. Remove EGR switch cover (1).
REMOVAL OF EGR SWITCH COVER
1. EGR switch cover.2. Install 5P298 Pin (4) in hole. The pin length in mm is given on the large diameter of the pin. Put spring (3) on pin (4) and install 5P6602 Adapter (2).
INSTALLATION OF ADAPTER
2. 5P6602 Adapter. 3. 3J6956 Spring. 4. 5P298 Zero Set Pin (with 17.8507 on it).3. Install 8S7271 Set Screw (6). Remove shut-off solenoid (5).
INSTALLATION OF SET SCREW
5. Solenoid. 6. 8S7271 Set Screw.4. Use wrench (7) and tighten set screw (6) until pin is against pump housing. Install collet clamp (11) in adapter (2). Install indicator (9) and point in collet clamp (11). Loosen nut (10). Move governor control lever (12) to full load position. Make an adjustment to the indicator (move indicator up or down) until both hands are at zero. Tighten nut (10) of the collet clamp. To make a fine adjustment to indicator (9), loosen lock (8). Turn bezel until large hand is on zero and tighten lock (8). Remove set screw (6) with wrench (7).
ADJUSTMENT OF DIAL INDICATOR
2. 5P6602 Adapter. 7. Wrench. 8. Lock. 9. Indicator. 10. Nut. 11. Collet clamp. 12. Governor control lever.5. Release governor control lever (12) and move it to low idle position. Connect the wire clip
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
7E1304
SHAFT-FAN
3116
3116
3116
6I4029
SHAFT-THROTTLE
3114, 3116, 3126
3114, 3116, 3126
9Y4549
SHAFT-STUB
3114, 3116, 3126
3114, 3116, 3126
7E1306
SHAFT-FAN
3116, 3126
3116, 3126
9Y3913
SHAFT
3406B
3406B
6I3989
SHAFT AS-TURBOCHARGER
3176, 3176B
3176, 3176B
1030649
SHAFT AS-TURBINE
3406B
3406B
4P3620
SHAFT AS-TURBINE
3406B, 3406C
3406B, 3406C
245D, 3406B, 3406E, D8L, D9N, D9R, R2900
3176, 3176B, 3176C, 3196, C-10, C-12, C-9, C11, C13, C9, CX31-C13I, CX31-C9I, TH31-E61, TH35-C11I, TH35-C13I, TH35-C13T
4P3172
SHAFT-OUTPUT
3176, 3176B
3176, 3176B