1294323 SHAFT-PLANETARY Caterpillar parts
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT38G II
Rating:
Alternative (cross code) number:
CA1294323
129-4323
1294323
CA1294323
129-4323
1294323
Weight: 6 pounds 3 kg.
Information:
EFFECTIVE LENGTH
91.9
mm
HEAD OD
0
mm
OVERALL LENGTH
103.3
mm
PIN OD
70.029
mm
TRANSV HOLES
Y
DETENT BALL
N
END TYPE A
CHAMFER
END TYPE B
CHAMFER
GROOVE
N
HAND RING
N
HEAD THICKNESS
0
KEEPER SLOT
N
LUBE OUTLETS
N
THREAD SIZE MAX
M12X1.75
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Related part:
1294323
SHAFT-PLNTY-YM
5222296
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$34.59
06 Feb 2022
US: Florida-Parts-Z
1294323 - Shaft-Planetary for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$38.61
17 Jun 2022
Amazon.com
1294323 Shaft - Planet CGR Ghinassi - Made in Italy
CGR Compatible Models - 966K 966G 966K 972K || PLANETARY GP BRAKE
CGR Compatible Models - 966K 966G 966K 972K || PLANETARY GP BRAKE
Compatible equipment models: 1294323:
Information:
Remove Crankshaft Main Bearings
START BY:a. remove piston cooling jetsb. remove oil pan 1. Use tool (A) to turn the engine flywheel to move counterweights (2) in position for the removal of the main bearing caps. If necessary, the counterweights can be removed.2. Remove the four bolts, and remove bearing caps (1) from the crankshaft. 3. Remove lower bearing halves (3) from bearing caps (1). 4. Remove thrust plates (4) from each side of the center main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
5. Install tool (B) in the oil hole in the crankshaft journal, and remove upper main bearing halves (5) as the crankshaft is turned and the bearing is moved out of the cylinder block. On the center main journal that has no oil hole, put a thin piece of soft material that will not damage the crankshaft journal against the end of the bearing, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the cylinder block. Remove the upper half of the main bearing.Install Crankshaft Main Bearings
Make sure the upper and lower halves of bearings are installed so the bearing tabs fit into the notch in cylinder block and bearing caps.
Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly. 1. Install tool (B) in the oil hole of the crankshaft. Put the upper bearing half (half with oil hole) in position on the crankshaft. Use tool (A) to turn the engine flywheel and push the bearing half in position with tool (B). 2. Put clean engine oil on thrust plates (1), and install the plates on each side of the center main bearing. 3. Make sure bearing caps (2) are clean, and install lower bearing halves (3) in the caps.
When Plastigage is used to check bearing clearances, do not use an impact wrench for the torque tightening sequence. For complete details concerning checking bearing clearances, see Engine Bearing And Crankshafts, Form No. SEBD0531.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances. 4. Check the bearing clearances with Plastigage as follows:a. Put a piece of the Plastigage on the surface of the lower bearing half.b. Install main bearing caps (2) with the word "FRONT" and the cast part number toward the front of the cylinder block. Each cap
START BY:a. remove piston cooling jetsb. remove oil pan 1. Use tool (A) to turn the engine flywheel to move counterweights (2) in position for the removal of the main bearing caps. If necessary, the counterweights can be removed.2. Remove the four bolts, and remove bearing caps (1) from the crankshaft. 3. Remove lower bearing halves (3) from bearing caps (1). 4. Remove thrust plates (4) from each side of the center main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
5. Install tool (B) in the oil hole in the crankshaft journal, and remove upper main bearing halves (5) as the crankshaft is turned and the bearing is moved out of the cylinder block. On the center main journal that has no oil hole, put a thin piece of soft material that will not damage the crankshaft journal against the end of the bearing, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the cylinder block. Remove the upper half of the main bearing.Install Crankshaft Main Bearings
Make sure the upper and lower halves of bearings are installed so the bearing tabs fit into the notch in cylinder block and bearing caps.
Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly. 1. Install tool (B) in the oil hole of the crankshaft. Put the upper bearing half (half with oil hole) in position on the crankshaft. Use tool (A) to turn the engine flywheel and push the bearing half in position with tool (B). 2. Put clean engine oil on thrust plates (1), and install the plates on each side of the center main bearing. 3. Make sure bearing caps (2) are clean, and install lower bearing halves (3) in the caps.
When Plastigage is used to check bearing clearances, do not use an impact wrench for the torque tightening sequence. For complete details concerning checking bearing clearances, see Engine Bearing And Crankshafts, Form No. SEBD0531.
When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances. 4. Check the bearing clearances with Plastigage as follows:a. Put a piece of the Plastigage on the surface of the lower bearing half.b. Install main bearing caps (2) with the word "FRONT" and the cast part number toward the front of the cylinder block. Each cap
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
4V4501
SHAFT-PLANETARY
611, 615, 615C, 816B, 966G, D25D, D400E, D40D, R1600, R1600G, R1600H
611, 615, 615C, 816B, 966G, D25D, D400E, D40D, R1600, R1600G, R1600H
1003976
SHAFT
918F, 924F, 928F, 938F, 938G, 938G II, IT18F, IT24F, IT28F, IT38F, IT38G, IT38G II
918F, 924F, 928F, 938F, 938G, 938G II, IT18F, IT24F, IT28F, IT38F, IT38G, IT38G II
6Y7880
SHAFT-PLANETARY
950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300G II
950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300G II
1465776
SHAFT AS-STEERING
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
3P3505
SHAFT-BRAKE
826C, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 972G, 980C, 980G, 980G II, 980H, 980K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, D44B, D550B
826C, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 972G, 980C, 980G, 980G II, 980H, 980K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, D44B, D550B
1123818
SHAFT-INPUT
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M
9W8433
SHAFT AS-OUTPUT
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980M, R1600, R1600G,...
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980M, R1600, R1600G,...
8P2042
SHAFT-PLANETARY
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 980C, 980F, 980F II, R1600, R1600G, R1600H, R1700 II, R1700G
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 980C, 980F, 980F II, R1600, R1600G, R1600H, R1700 II, R1700G
6Y3148
SHAFT-OUTPUT
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, R1300, R1300G
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, R1300, R1300G
3615740
SHAFT AS-STEERING
950H, 962H, 966H, 972H, 980H
950H, 962H, 966H, 972H, 980H
1295400
SHAFT-BEVEL PINION
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K
9C8218
SHAFT-BEVEL PINION
814B, 815B, 816B, 966D, 966F, 966G
814B, 815B, 816B, 966D, 966F, 966G
2320931
SHAFT-AXLE
950G II, 950H, 950K, 962G II, 962H, 962K, IT62G II
950G II, 950H, 950K, 962G II, 962H, 962K, IT62G II
2659465
SHAFT-OUTPUT
950G, 950G II, 950H, 950K, 962G II, 962H, 962K, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G II, 962H, 962K, IT62G II, IT62H
2047186
SHAFT AS
938G II, 938H, IT38G II, IT38H
938G II, 938H, IT38G II, IT38H
3569931
SHAFT
621G, 621H, 621K, 623G, 623H, 623K, 623K LRC, 627G, 627H, 627K, 627K LRC, 631G, 637G, 657G, 950H, 950K, 962H, 962K
621G, 621H, 621K, 623G, 623H, 623K, 623K LRC, 627G, 627H, 627K, 627K LRC, 631G, 637G, 657G, 950H, 950K, 962H, 962K
1741445
SHAFT AS
IT14G, IT14G2
IT14G, IT14G2
1712521
SHAFT AS-LOWER
621G, 623G, 627G, 631G, 637G, 657G
621G, 623G, 627G, 631G, 637G, 657G
2032757
SHAFT-PINION
928H, 928HZ, IT28G
928H, 928HZ, IT28G
2421830
SHAFT-PINION
924K, 928HZ, 930G, 930K, IT28G
924K, 928HZ, 930G, 930K, IT28G
1278910
SHAFT-AXLE
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT38G II
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT38G II
1333574
SHAFT-BEVEL PINION
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, IT38G II
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, IT38G II
3724787
SHAFT-PINION
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT38G II
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT38G II
1027511
SHAFT-PINION
966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, IT38G II
966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, IT38G II