1532686 SHAFT Caterpillar parts
312, 312B L, 312C
Rating:
Alternative (cross code) number:
CA1532686
153-2686
1532686
CA1532686
153-2686
1532686
Weight: 1 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
6
For full view, you need register
Information:
Removal Procedure
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the filler cap is cool enough to touch with the bare hand.Remove the filler cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with skin and eyes to prevent personal injury.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Open the engine access door and the hood.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper draining procedure.
Illustration 1 g01249147
Disconnect hose assembly (1) .
Loosen clamp (4) and disconnect the hose.
Remove bolts (2) and remove bonnet (3) .
Illustration 2 g01249148
Remove plug (7) and drain the oil from the oil filter base.
Remove bolts (6) .
Remove engine oil cooler (5) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 3 g01249148
Position engine oil cooler (5) .
Install bolts (6) .
Install plug (7) .
Illustration 4 g01249147
Position bonnet (3) and install bolts (2) .
Install hoses (4) and tighten the clamps.
Connect hose assembly (1) .
Close the engine access door.
Fill the cooling system. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure.
Close the hood and the engine access door.
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the filler cap is cool enough to touch with the bare hand.Remove the filler cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with skin and eyes to prevent personal injury.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Open the engine access door and the hood.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper draining procedure.
Illustration 1 g01249147
Disconnect hose assembly (1) .
Loosen clamp (4) and disconnect the hose.
Remove bolts (2) and remove bonnet (3) .
Illustration 2 g01249148
Remove plug (7) and drain the oil from the oil filter base.
Remove bolts (6) .
Remove engine oil cooler (5) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 3 g01249148
Position engine oil cooler (5) .
Install bolts (6) .
Install plug (7) .
Illustration 4 g01249147
Position bonnet (3) and install bolts (2) .
Install hoses (4) and tighten the clamps.
Connect hose assembly (1) .
Close the engine access door.
Fill the cooling system. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure.
Close the hood and the engine access door.
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
206, 212, 3054, 307, 312, 315, 317, 416B, 416C, 426B, 426C, 428, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433B, CP-433C, CS-323C,...
3054, 3054B, 3056, 3056E, 307, 312B L, 312C, 315B L, 416B, 416C, 416D, 420D, 424D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908, 914G, 924G, 924GZ, AP-80...
311, 311B, 312, 312B, 315, 315B L, 315C, 317, 317B LN, 318B, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 321C, 325D, 329D L, 345C L, OEMS
311, 311B, 311C, 312, 312B, 315, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, E120B
311, 311B, 312, 312B, 312B L, 313B
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN...
1655803
SHAFT
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
2671628
SHAFT-DRIVE
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L, 319D, 319D L, 319D LN
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L, 319D, 319D L, 319D LN
311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D...
1469661
SHAFT
312, 312B L
312, 312B L
311, 311B, 312, 312B, 312B L, 313B
311, 312
311, 311B, 312, 312B, 312B L, 313B, 315, 315B L, 315C, 317, 317B LN, 318B, E110B, E120B
7I7786
SHAFT-PLANETARY
311, 311B, 312, 312B, 312B L, 313B, 315, 315B, 315B L, 315C, 317, 317B LN, 318B, E110B, E120B
311, 311B, 312, 312B, 312B L, 313B, 315, 315B, 315B L, 315C, 317, 317B LN, 318B, E110B, E120B
M312, M313C, M315, M315C, M316C, M318, M318C
1141325
SHAFT-PINION
315, 315B, 315B L, 317, 317B LN
315, 315B, 315B L, 317, 317B LN
315, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 319C, 319D, 319D LN, 320 L, 320B, 320C, 320D, 320D FM, 320D L, 320D2, 322B LN, 322C, 323D L, 323D LN, 323D2 L, 324D, 324D L, 324D LN, 325D, 329D L,...
6I5364
SHAFT
312, 315, 317, 325 L, 330 L, 350, 375, 375 L, 5130, 5230
312, 315, 317, 325 L, 330 L, 350, 375, 375 L, 5130, 5230
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN