SHAFT 1687087 - Caterpillar

1687087 SHAFT Caterpillar parts M312, M315

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1687087
168-7087
1687087

Weight: 1 pounds 0 kg.

Buy SHAFT 1687087 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEELED EXCAVATOR,

This part in 2 request: Show. This information for suppliers only!

#664277 1687087

2021-06-07

#6224 168-7087

2016-05-30

Compatible equipment models: 1687087:

WHEELED EXCAVATOR M312 M315 Caterpillar

Number on catalog scheme: 7

For full view, you need register

Information:

Illustration 1 g02041353
Schematic of the front track position sensorThis diagnostic code is associated with the front track position sensor. The FMI F13 means that the ECM has determined that the sensor signal is not properly calibrated. The possible causes of this failure are listed below:
The sensor may not be calibrated properly.
The ECM has been flashed with new software.
The sensor has failed.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Clear these diagnostic codes when the original diagnostic code has been corrected. Also, ensure that the CID 743 FMI F03 or FMI F04 are not active. Ensure that the diagnostic code of CID 743 FMI F13 is active before performing this procedure.System Response:The machine response is listed below:
A Category 2 warning is shown on the Computerized Monitoring System (CMS) for the sensor.
A fault on the front track position sensor will cause the steering to not move to the full right or full left positions.
A fault on the front track position sensor will only allow steering in the FRONT position.Test Step 1. CHECK THE CALIBRATION OF THE SENSOR
Perform the necessary adjustment and calibration procedures for the front track position sensor. Refer to the Testing and Adjusting, "Front Steering Sensor - Calibrate" section of the service manual for these procedures. Always do the sensor calibration in the following conditions:
FULL RIGHT (c10)
CENTER/STRAIGHT (c11)
"FULL LEFT" (c12)
Observe the status of the CID 743 FMI F13.Results:
OK - The CID 743 FMI F13 is not active. The calibration corrected the condition that caused the CID 743 FMI F13. Resume normal operation.STOP
NOT OK - The CID 743 FMI F13 is still active.Repair: The diagnostic code is still active. Verify that the correct software has been flashed into the ECM, or that the correct ECM is installed on the machine. Then repeat the calibration. If the diagnostic code is still active and the cause of the diagnostic code is not found replace the ECM. It is unlikely that the ECM has failed. Verify that the sensor and associated circuits are correct before you replace the ECM.STOP

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

M315 Excavator 7ML00001-00859 (MACHINE) POWERED BY 3054 Engine

120-4712: DRIVE GP-SWING » (16 TEETH) SEBP24300283

M312 Excavator 6TL00001-00409 (MACHINE) POWERED BY 3054 Engine

120-4712: DRIVE GP-SWING » (16 TEETH) SEBP24330257

M312 Excavator 6TL00410-UP (MACHINE) POWERED BY 3054 Engine

120-4712: DRIVE GP-SWING » (16 TEETH) SEBP28510357

M315 Excavator 7ML00860-UP (MACHINE) POWERED BY 3054 Engine

120-4712: DRIVE GP-SWING » (16 TEETH) SEBP28520375

Parts shaft Caterpillar catalog:

0329007 SHAFT AS
206, 212, 3054, 307, 312, 315, 317, 416B, 416C, 426B, 426C, 428, 428B, 428C, 436C, 438C, 914G, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433B, CP-433C, CS-323C,...

1273294 SHAFT
3054, 3054B, 3056, 3056E, 307, 312B L, 312C, 315B L, 416B, 416C, 416D, 420D, 424D, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 550B, 554, 560B, 564, 574B, 908, 914G, 924G, 924GZ, AP-80...