SHAFT GP-HYDRAULIC MOTOR 1802652 - Caterpillar

Features/Benefits
* Used to remove sleeve bearings from boom and stick - essential to remove bearing sleeves used on 300, M300, and 5000 Series Excavators.* Also used to pull any bearing with appropriate size inside diameter.* Bearing puller adapters allow easy removal of sleeve bearings and reduce chance of damage to bearing bore.* Sides are cut away to allow adpater to be put through bearing in a sideways position and then turned up to engage against backside of bearing.* Used with the following tooling, when adapter plate has M64 threaded holes: 4C-6504 Threaded Puller Rod, 9U-6800 Fast Runner Nut, 5P-5201 Hydraulic Cylinder, 3S-6224 Hydraulic Pump - 115 VAC or 8S-8033 Hydraulic Pump - 230 VAC, and 6D-7726 Hydraulic Hose.* Used with the following tooling, when adapter plate has 1 1/4-12 threaded holes: 4C-3694 Threaded Puller Rod, 9U-6832 Fast Runner Nut or 7H-7539 Nut, 4K-0684 Washer, Hardened (1 1/4 in), 6V-3175 Hydraulic Cylinder, 3S-6224 Hydraulic Pump - 115 VAC or 8S-8033 Hydraulic Pump - 230 VAC, and 6D-7726 Hydraulic Hose* A 1 1/4-12 threaded puller rods and 7H-7539 NutSpecifications/Technical Information
Bearing Puller Adapter Plates
Part No. Bearing ID Adapter OD (1) Adapter OD (2) Threaded Hole(3)
123-3804 Adapter, Bearing Puller 60.0 (2.36) 70.0 (2.76) 59.0 (2.32) 1 1/4-129U-5336 Adapter, Bearing Puller 70.0 (2.76) 81.0 (3.19) 69.0 (2.72) 1 1/4-129U-5337 Adapter, Bearing Puller 80.0 (3.15) 91.0 (3.58) 79.0 (3.11) 1 1/4-12 9U-5338 Adapter, Bearing Puller 90.0 (3.54) 102.0 (4.02) 89.0 (3.50) 1 1/4-129U-5339 Adapter, Bearing Puller 100.0 (3.94) 112.0 (4.41) 99.0 (3.90) 1 1/4-129U-6227 Adapter, Bearing Puller 110.0 (4.33) 126.0 (4.96) 109.0 (4.29) 1 1/4-129U-6907 Adapter, Bearing Puller 120.0 (4.72) 145.4 (5.72) 119.0 (4.69) 1 1/4-129U-6260 Adapter, Bearing Puller 130.0 (5.12) 150.0 (5.91) 129.0 (5.08) 1 1/4-129U-6261 Adapter, Bearing Puller 140.0 (5.51) 160.00 (6.30) 139.0 (5.47) 1 1/4-121U-6217 Adapter, Bearing Puller 160.0 (6.30) 185.4 (7.30) 159.0 (6.26) 1 1/4-12 123-8527 Adapter, Bearing Puller 170.0 (6.69) 195.4 (7.69) 169.0 (6.65) M64 x 69U-6904 Adapter, Bearing Puller 200.0 (7.87) 225.4 (8.87) 199.0 (7.83) M64 x 69U-6906 Adapter, Bearing Puller 220.0 (8.66) 245.4 (9.66) 219.0 (8.62) M64 x 69U-6905 Adapter, Bearing Puller 240.0 (9.45) 285.1 (11.22) 239.0 (9.41) M64 x 61U-6203 Adapter, Bearing Puller 280.0 (11.02) 315.4 (12.41) 279.0 (10.98) M64 x 61U-6204 Adapter, Bearing Puller 300.0 (11.81) 345.4 (13.60) 299.0 (11.77) M64 x 6 All measurements are in millimeters (inches).
Typical bearing puller adapter (See chart for specifications)(1) Bearing adapter, large OD.(2) Bearing adapter, small OD.(3) Threaded hole. (1) (2) (3)
Installation of bearing sleeve tooling on stick assembly(1) Hydraulic cylinder(2) Threaded puller rod(3) Sleeve bearing(4) Bearing puller adapter plateReference: Service Manual Modules; 5000 Series Excavator; Disassembly and Assembly; 300 Series Excavator; Disassembly and Assembly; M300 Series Excavator; Disassembly and Assembly; Special Instruction; SEHS9721; Assembly Procedure for Hydraulic Excavator (5130 Excavator only)