2335174 SHAFT-THROTTLE Caterpillar parts
216, 228, 236, 247, 248, 267, 287, 3034, 906
Rating:
Alternative (cross code) number:
CA2335174
233-5174
2335174
CA2335174
233-5174
2335174
Weight: 0.08 pounds 0 kg.
COMPACT WHEEL LOADER, SKID STEER LOADER,
Compatible equipment models: 2335174:
Information:
Adjustment of the Oil Change Interval
Note: Your Cat dealer has additional information on these programs.Program A
Verification for an Oil Change Interval of 500 HoursThis program consists of three oil change intervals of 500 hours. Oil sampling and analysis are done at 250 hours and 500 hours for each of the three intervals for a total of six oil samples. The analysis includes oil viscosity and infrared (IR) analysis of the oil. If all of the results are satisfactory, the 500 hour oil change interval is acceptable for the machine in that application. Repeat Program A if you change the application of the machine.If a sample does not pass the oil analysis, take one of these actions:
Shorten the oil change interval to 250 hours.
Proceed to Program B.
Change to a preferred oil type in Table 1.Program B
Optimizing Oil Change IntervalsBegin with a 250 hour oil change interval. The oil change intervals are adjusted by increments. Each interval is adjusted an additional 50 hours. Periodic oil sampling and analysis is done during each interval. The analysis includes oil viscosity and infrared (IR) analysis of the oil. Repeat Program B if you change the application of the machine.If an oil sample does not pass the analysis, shorten the oil change interval, or change to a preferred multigrade oil type in the listing above.Procedure for Changing Engine Oil and Filter
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Note: If the sulfur content in the fuel is greater than 1.5 percent by weight, use an oil that has a TBN of 30 and reduce the oil change interval by one-half.Note: Drain the crankcase while the oil is warm. This allows waste particles that are suspended in the oil to drain. As the oil cools, the waste particles will settle to the bottom of the crankcase. The particles will not be removed by draining the oil and the particles will recirculate in the engine lubrication system with the new oil.Note: Run the engine at low idle for at least ten minutes before performing any other operations every time the engine oil and oil filter are changed in order to protect your engine. Refer to Operations and Maintenance Manual, "Engine and Machine Warm-up".
Park the machine on a level surface. Stop the engine.
Illustration 1 g03713824Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on Containing Fluid Spillage.
The drain valve for the engine crankcase oil is located under the engine on the right side of the machine. Remove cover (1) and open crankcase drain valve (2). Allow the oil to drain into a suitable container. Note: Discard any drained fluids according to local regulations.
Close the drain valve and replace the cover.
Open the engine access door at the right side of the machine.
Illustration 2 g03884023
Remove used oil filter (3). See Operation and Maintenance Manual, "Oil Filter - Inspect". Note: Maintain the vertical position of the filter until you can dispose of the filter and oil properly. Tilting
Note: Your Cat dealer has additional information on these programs.Program A
Verification for an Oil Change Interval of 500 HoursThis program consists of three oil change intervals of 500 hours. Oil sampling and analysis are done at 250 hours and 500 hours for each of the three intervals for a total of six oil samples. The analysis includes oil viscosity and infrared (IR) analysis of the oil. If all of the results are satisfactory, the 500 hour oil change interval is acceptable for the machine in that application. Repeat Program A if you change the application of the machine.If a sample does not pass the oil analysis, take one of these actions:
Shorten the oil change interval to 250 hours.
Proceed to Program B.
Change to a preferred oil type in Table 1.Program B
Optimizing Oil Change IntervalsBegin with a 250 hour oil change interval. The oil change intervals are adjusted by increments. Each interval is adjusted an additional 50 hours. Periodic oil sampling and analysis is done during each interval. The analysis includes oil viscosity and infrared (IR) analysis of the oil. Repeat Program B if you change the application of the machine.If an oil sample does not pass the analysis, shorten the oil change interval, or change to a preferred multigrade oil type in the listing above.Procedure for Changing Engine Oil and Filter
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.
Note: If the sulfur content in the fuel is greater than 1.5 percent by weight, use an oil that has a TBN of 30 and reduce the oil change interval by one-half.Note: Drain the crankcase while the oil is warm. This allows waste particles that are suspended in the oil to drain. As the oil cools, the waste particles will settle to the bottom of the crankcase. The particles will not be removed by draining the oil and the particles will recirculate in the engine lubrication system with the new oil.Note: Run the engine at low idle for at least ten minutes before performing any other operations every time the engine oil and oil filter are changed in order to protect your engine. Refer to Operations and Maintenance Manual, "Engine and Machine Warm-up".
Park the machine on a level surface. Stop the engine.
Illustration 1 g03713824Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on Containing Fluid Spillage.
The drain valve for the engine crankcase oil is located under the engine on the right side of the machine. Remove cover (1) and open crankcase drain valve (2). Allow the oil to drain into a suitable container. Note: Discard any drained fluids according to local regulations.
Close the drain valve and replace the cover.
Open the engine access door at the right side of the machine.
Illustration 2 g03884023
Remove used oil filter (3). See Operation and Maintenance Manual, "Oil Filter - Inspect". Note: Maintain the vertical position of the filter until you can dispose of the filter and oil properly. Tilting
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
1377748
SHAFT GP-DRIVE
902, 906
902, 906
2104640
SHAFT AS
247, 247B, 267B, 287
247, 247B, 267B, 287
2104641
SHAFT AS
247, 247B, 267B, 287
247, 247B, 267B, 287
2157488
SHAFT
416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 442D, 442E, 450E, 450F, 902, 906, 906H, 906H2, 907H, 907H2, 908H, 908H2, TH220B, TH330B, TH3...
416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 442D, 442E, 450E, 450F, 902, 906, 906H, 906H2, 907H, 907H2, 908H, 908H2, TH220B, TH330B, TH3...
2225686
SHAFT-AXLE
267B, 287
267B, 287
2225682
SHAFT
267B, 287
267B, 287
2110093
SHAFT
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, CP-433E, CP-44, CS-423E, CS-433E, CS-44, TH210, TH215
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2, CP-433E, CP-44, CS-423E, CS-433E, CS-44, TH210, TH215
2053020
SHAFT-PUMP
3034
3034
1521206
SHAFT AS
902, 906, 908
902, 906, 908
2110104
SHAFT-DRIVE
902, 906, 908
902, 906, 908
1420274
SHAFT GP-DRIVE
902, 906
902, 906
2246681
SHAFT AS
902, 906, 908
902, 906, 908
1587924
SHAFT
216, 236, 3034, 906
216, 236, 3034, 906
2063499
SHAFT-ROCKER ARM
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3024, 3024C, 304.5, 902, AP-255E, BB-621C, C2.2, CB-334E, CB-34, CB34B, CB34B XW, CC34B
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3024, 3024C, 304.5, 902, AP-255E, BB-621C, C2.2, CB-334E, CB-34, CB34B, CB34B XW, CC34B
1526573
SHAFT AS-ROCKER ARM
216, 228, 236, 247, 248, 267, 287, 3034, 906
216, 228, 236, 247, 248, 267, 287, 3034, 906
1526559
SHAFT
216, 228, 236, 247, 248, 267, 287, 3034, 906
216, 228, 236, 247, 248, 267, 287, 3034, 906
1625403
SHAFT AS
35, 45, 55
35, 45, 55
1154116
SHAFT AS
120H, 120H ES, 120H NA, 135H, 135H NA, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 35, 45, 525B, 533, 535B, 539, 55, 550, 570, 570B, 574, 580, 580B, 613C II, 928G, 950G, 953C, 962G, AP-1000B, AP-10...
120H, 120H ES, 120H NA, 135H, 135H NA, 3116, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 35, 45, 525B, 533, 535B, 539, 55, 550, 570, 570B, 574, 580, 580B, 613C II, 928G, 950G, 953C, 962G, AP-1000B, AP-10...
1230856
SHAFT-FAN
3116, 3126, 3126B, 3126E, 570B, 573, 580B, C-9, C7, C9, CX31-C9I, MTC735, TH31-E61
3116, 3126, 3126B, 3126E, 570B, 573, 580B, C-9, C7, C9, CX31-C9I, MTC735, TH31-E61
3P5478
SHAFT AS
572G, D7F
572G, D7F
3P5476
SHAFT AS
D7F
D7F
2P4701
SHAFT AS-GEAR
571G, 572G, D6C, D7F, D7G, D7G2
571G, 572G, D6C, D7F, D7G, D7G2
1059772
SHAFT-DRIVE IDLER
120G, 12G, 12H, 12H NA, 140G, 140H, 140H NA, 160H, 235C, 235D, 3304, 3304B, 3306, 330B, 350, 639D, 973, 973C, CB-534, D4E SR, D5B, D5E, D5H, D5H XL, D6D, D6E, D6E SR, D6G SR, D6H, D6H XL, D6H XR, D6R,...
120G, 12G, 12H, 12H NA, 140G, 140H, 140H NA, 160H, 235C, 235D, 3304, 3304B, 3306, 330B, 350, 639D, 973, 973C, CB-534, D4E SR, D5B, D5E, D5H, D5H XL, D6D, D6E, D6E SR, D6G SR, D6H, D6H XL, D6H XR, D6R,...
1910542
SHAFT
216, 216B, 226B, 232B, 242B, 247B, 257B, 3013, 3013C, 3014, 302.5, 3024, 3024C, 303.5, 304.5, 902, C1.5, C2.2, CB-214D, CB-214E, CB-334D, CB-334E, CB-335D
216, 216B, 226B, 232B, 242B, 247B, 257B, 3013, 3013C, 3014, 302.5, 3024, 3024C, 303.5, 304.5, 902, C1.5, C2.2, CB-214D, CB-214E, CB-334D, CB-334E, CB-335D