2514251 SHAFT Caterpillar parts
545D, 555D, 966H, 972G II, 972H, 972K
Rating:
Alternative (cross code) number:
CA2514251
251-4251
2514251
CA2514251
251-4251
2514251
Weight: 8 pounds 3 kg.
WHEEL LOADER, WHEEL SKIDDER,
Compatible equipment models: 2514251:
Number on catalog scheme:
4
For full view, you need register
Information:
Adjustment Procedure For The Parking Brake Control
Chock the wheels.
Illustration 1 g01383365
Parking Brake Lever in the ENGAGED Position (1) Parking brake lever (2) Release lever for the parking brake lock (3) Knob for fine adjustment
Place the parking brake in the DISENGAGED position. Depress the release lever (2) and push the parking brake lever (1) downward.
Illustration 2 g01426290
Parking Brake Control (1) Parking brake lever (2) Release lever for the parking brake lock (3) Knob for fine adjustment (5) Brake disc (6) Nut (7) Nut
Loosen nut (6) and nut (7) .
Tighten nut (7) to 12 2 N m (8.9 1.5 lb ft).
Turn nut (7) counterclockwise for 5/6 turn. Verify that the brake disc (5) rotates freely.
Tighten nut (6) against nut (7). Tighten nut (6) to 60 to 75 N m (45 to 55 lb ft).
Remove the chocks from the wheels.Note: Test the brakes on a dry, level surface.
Check the area around the machine. Make sure that the machine is clear of personnel and clear of obstacles.
Fasten the seat belt before you test the brakes.
If the machine is equipped with All Wheel Drive, place the machine in Two-Wheel Drive.
Engage the parking brake. Pull the parking brake lever (1) upward in order to engage the parking brake .
Start the engine. Raise the bucket slightly.
Perform the parking brake test and adjust for machines that are equipped with a power shift transmission.
If the machine begins to move, reduce the engine speed immediately and apply the service brake pedal.
Move the transmission control lever to THIRD SPEED FORWARD, to NEUTRAL, and back to THIRD SPEED FORWARD position. This is done in order to override the transmission neutralizer for this test. An audible alarm will sound and the alert indicator will light.
Gradually increase the engine speed to high idle. The machine should not move.Note: If the machine moves perform steps 13.c through 13.h. If the machine does not move, proceed to step 14.
Place the transmission control lever in the NEUTRAL position.
Lower the bucket to the ground and stop the engine.
Place the parking brake in the DISENGAGED position.
Turn the fine adjustment knob (3) clockwise for one to two turns.
Tighten the setscrew (4) .
Repeat steps 11,12 and 13.
Reduce the engine speed. Move the transmission to NEUTRAL. Lower the bucket to the ground. Stop the engine.
Chock the wheels.
Illustration 1 g01383365
Parking Brake Lever in the ENGAGED Position (1) Parking brake lever (2) Release lever for the parking brake lock (3) Knob for fine adjustment
Place the parking brake in the DISENGAGED position. Depress the release lever (2) and push the parking brake lever (1) downward.
Illustration 2 g01426290
Parking Brake Control (1) Parking brake lever (2) Release lever for the parking brake lock (3) Knob for fine adjustment (5) Brake disc (6) Nut (7) Nut
Loosen nut (6) and nut (7) .
Tighten nut (7) to 12 2 N m (8.9 1.5 lb ft).
Turn nut (7) counterclockwise for 5/6 turn. Verify that the brake disc (5) rotates freely.
Tighten nut (6) against nut (7). Tighten nut (6) to 60 to 75 N m (45 to 55 lb ft).
Remove the chocks from the wheels.Note: Test the brakes on a dry, level surface.
Check the area around the machine. Make sure that the machine is clear of personnel and clear of obstacles.
Fasten the seat belt before you test the brakes.
If the machine is equipped with All Wheel Drive, place the machine in Two-Wheel Drive.
Engage the parking brake. Pull the parking brake lever (1) upward in order to engage the parking brake .
Start the engine. Raise the bucket slightly.
Perform the parking brake test and adjust for machines that are equipped with a power shift transmission.
If the machine begins to move, reduce the engine speed immediately and apply the service brake pedal.
Move the transmission control lever to THIRD SPEED FORWARD, to NEUTRAL, and back to THIRD SPEED FORWARD position. This is done in order to override the transmission neutralizer for this test. An audible alarm will sound and the alert indicator will light.
Gradually increase the engine speed to high idle. The machine should not move.Note: If the machine moves perform steps 13.c through 13.h. If the machine does not move, proceed to step 14.
Place the transmission control lever in the NEUTRAL position.
Lower the bucket to the ground and stop the engine.
Place the parking brake in the DISENGAGED position.
Turn the fine adjustment knob (3) clockwise for one to two turns.
Tighten the setscrew (4) .
Repeat steps 11,12 and 13.
Reduce the engine speed. Move the transmission to NEUTRAL. Lower the bucket to the ground. Stop the engine.
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
517, 527, 561M, 561N, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, 966R, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D...
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345D, 345D L, 345D L VG, 349D, 349D L, 525D, 535D, 5...
950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300G II
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, IT38G II
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 980C, 980F, 980F II, R1600, R1600G, R1600H, R1700 II, R1700G
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, R1300, R1300G
950H, 962H, 966H, 972H, 980H
966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K
1741405
SHAFT
980G II, 980H, 980K
980G II, 980H, 980K
325 L, 784B, 785B, 785C, 789B, 789C, 793B, 793C, 994D
834G, 834H, 836G, 836H, 988G, 988H
2235836
SHAFT
834G, 834H, 834K, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD55, AD55B, AD60
834G, 834H, 834K, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD55, AD55B, AD60
1361756
SHAFT
834G, 834H, 836G, 836H, 988G, 988H
834G, 834H, 836G, 836H, 988G, 988H
1361750
SHAFT AS
834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
3382116
SHAFT AS-SLIP
834G, 834H, 836G, 836H, 988G, 988H
834G, 834H, 836G, 836H, 988G, 988H
3147839
SHAFT AS
834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
1946851
SHAFT
844, 990 II
844, 990 II
1796907
SHAFT
550, 550B, 560B, 570, 570B, 580, 580B, 844, 990 II, 990H
550, 550B, 560B, 570, 570B, 580, 580B, 844, 990 II, 990H
1974164
SHAFT AS
950G II, 962G II, 966G II, 972G II, 980G II, 980H
950G II, 962G II, 966G II, 972G II, 980G II, 980H
966G II, 966H, 966K, 966M, 966M XE, 972G II, 972H, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M, D8N