AVSPARE.COM
parts catalog

SHAFT 2H9182 - Caterpillar



2H9182 SHAFT Caterpillar parts D337 SHAFT
Rating:
63
Alternative (cross code) number:
CA2H9182
2H-9182
2H9182
Caterpillar 2H9182 SHAFT

Buy SHAFT 2H9182 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: 2H9182:

MARINE ENGINE  D337   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:

1. Disconnect the two oil lines connected to the oil pump.2. Remove two bolts (1) and remove transmission oil pump (2). 3. Remove bolt (3) and retainer (4) that hold pump drive gear (5) in place. Remove pump drive gear (5). The following steps are for installation of the transmission oil pump and drive gear.4. Put pump drive gear (5) in place in the transmission and install retainer (4) and bolt (3).5. Make sure the O-ring seal is in position, and install transmission oil pump (2). Install bolts (1) that hold the pump to the transmission case.Disassemble And Assemble Transmission Oil Pump And Pump Drive Gear (3F/3R Power Shift)
Start By:a. remove transmission oil pump and pump drive gear 1. Remove O-ring seal (2) from cover (3), bolts (1) and cover (3) from the pump body. 2. Remove bearings (4) from cover (3). 3. Remove drive gear (7), driven gear (6) and O-ring seal (5) from the pump body. 4. Remove bearings (8) from pump body (9). 5. Remove spiral lockring (10), shaft (11) and bearing (12) from gear (13). The following are assembly steps of the transmission oil pump and drive gear.6. Make sure all of the parts of the transmission oil pump and pump drive gear are clean. Put clean oil on all the parts of the pump and gear. Inspect all parts for damage and make replacements if needed.7. Install bearing (12) and shaft (11) in gear (13) with spiral lockring (10) to hold the bearing in place.
Make sure the joint in both bearings (8) are in the correct location. The location of the joint is an angle of 30° 15° from the center line of the two bearing bores in the direction of groove (14) on surface (15).
8. Install two bearings (8) into pump body (9) with tooling (A) and a press. The distance from the top of the bearing to surface (15) after assembly is 1.50 0.25 mm (.059 .010 in.).9. Install O-ring seal (5), driven gear (6) and drive gear (7) in pump body (9).
Make sure the joint in both bearings (4) are in the correct location. The location of the joint is an angle 30° 15° from the centerline of the two bearing bores in the direction of groove (16) on surface (17).
10. Install two bearings (4) in cover (3) with tooling (A). The distance from the top of the bearing to surface (17) after assembly is 1.50 0.25 mm (.059 .010 in.).11. Install O-ring seal (2) on cover (3). Install cover on pump body (9) with bolts (1). Pump must turn freely by hand after assembly.End By:a. install transmission oil pump and pump drive gear

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455


Parts shaft Caterpillar catalog:

3B1304 SHAFT
12E, 16, 1693, 583H, 621, 641B, 651, 657, 666, 772, 777, 955C, 977H, 988, 992, D10, D315, D320A, D326F, D337, D342, D342C, D343, D348, D353C, D375D, D379A, D398, D399, D8H, D9E, D9G, D9H
7F1608 SHAFT
955C, D326F, D337, D337F, D364
9F1594 SHAFT
16, 1693, 594, 657, 769, 988, D326F, D337, D337F, D343, D353C, D9E, D9G
9F8681 SHAFT
D326F, D337, D337F, D342, D342C, D375D, D397D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.