2H9454 SHAFT Caterpillar parts SHAFT
Rating:
Alternative (cross code) number:
CA2H9454
2H-9454
2H9454
CA2H9454
2H-9454
2H9454

Weight: 0.25 pounds 0 kg.
Buy SHAFT 2H9454 Caterpillar genuine, new aftermarket tractor parts with delivery
Information:
Illustration 1 g01269296
Schematic of the Implement Lockout SwitchThis diagnostic code is recorded when the status of both the normally open inputs and normally closed inputs are grounded. This switch has two inputs to the ECM. The inputs are normally open and normally closed. During proper operation, one input is open and the other input is grounded.The possible causes of this diagnostic code are listed:
The normally open circuit is shorted to ground while the normally closed circuit is grounded through the switch.
The normally closed circuit is shorted to ground while the normally open circuit is grounded through the switch.
The normally open circuits and the normally closed circuits are shorted to ground in the harness.
The normally open circuits and normally closed circuits are shorted together. The switch must be in one specific position.
The switch has failed.System Response:The machine response is listed:
The implements will not work.Table 1 contains wire numbers and connector contacts. Use this information to troubleshoot the failed circuit.
Table 1
Switch Continuity    
Switch / CID     Switch State     Implement ECM Connector Contact No.     Switch Contact     Wire No.     Status    
CID 0490 Implement Lockout Switch     Not Locked     J1-43 N/O (1)     N/O     E917-WH     O (2)    
J1-42 N/C (3) N/C     E918-GN     G (4)    
Locked J1-43 N/O     N/O     E917-WH     G    
J1-42 N/C N/C     E918-GN     O    
( 1 ) N/O means Normally Open.
( 2 ) O means Open (no continuity to ground).
( 3 ) N/C means Normally Closed.
( 4 ) G means Grounded ( continuity to ground).Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code is corrected.Ensure that the diagnostic code is active. Test Step 1. CHECK THE SWITCH.
Observe ON/OFF status of the diagnostic code indicator.
Disconnect the connector of the switch from the harness.Expected Result:The diagnostic code remains active.Results:
YES - The diagnostic code remains active. The switch is not the cause of the diagnostic code. Proceed to test step 2 .
NO - The diagnostic code is inactive. The switch has failed or the harness has failed.Repair: Repeat this test in order to verify the failure of the switch. Repair the switch or replace the switch. Repair the harness or replace the harness.STOPTest Step 2. CHECK THE HARNESS CIRCUIT.
This test checks the continuity of the entire harness circuit that has failed. This test includes the switch that was previously checked.
Reconnect the switch that was disconnected in the previous step.
Disconnect the harness from the ECM.
Activate the switch. At the harness connector for the ECM, check the continuity to ground of the normally closed contact and the normally open contact.Expected Result:The continuity agrees with table 1.Results:
YES - The continuity agrees with the values in the preceding table. The harness circuit is correct.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this troubleshooting procedure again. If the cause of the diagnostic code is
Parts shaft Caterpillar catalog:
2H9441
SHAFT
Caterpillar
Caterpillar
2H9307
SHAFT A.-UPPER
Caterpillar
Caterpillar
2H9252
SHAFT-CONTROL
Caterpillar
Caterpillar
2H8914
SHAFT A
Caterpillar
Caterpillar
2H8576
SHAFT A.
Caterpillar
Caterpillar
2H8480
SHAFT
Caterpillar
Caterpillar
2I5270
SHAFT A
Caterpillar
Caterpillar
2I5268
SHAFT
Caterpillar
Caterpillar
2I5237
SHAFT
Caterpillar
Caterpillar
2I5161
SHAFT
Caterpillar
Caterpillar
2H9635
SHAFT
Caterpillar
Caterpillar
2H9467
SHAFT
Caterpillar
Caterpillar