SHAFT AS 3119649 - Caterpillar

Testing and Adjusting
Refer to the following procedures ensure that the machine is functioning properly:
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Steering System Pressure (High Pressure Stall) - Test and Adjust"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Torque Converter Stall and Implement Pump Double Stall - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Manifold and Relief Valve (Main) - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Pilot System Pressure - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Service Brake System Pressure - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Brake Accumulator - Test and Charge"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Service Brakes - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Torque Converter Impeller Clutch Pressure - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Torque Converter Lockup Clutch Pressure - Test"
Testing and Adjusting, UENR4599, "844K Wheel Dozer Machine Systems", "Transmission Pressures - Test and Adjust"Test Product Link
Product Link may need up to 15 minutes establish communication with a satellite. Allow a minimum of 15 minutes to complete the following procedure. establish communication, the antenna for the Product Link module must have a clear view of the sky. Objects that obstruct the antennas view of the sky may result in a failure. If the antenna was obstructed during the test, retest the Product Link system with an unobstructed view of the sky. Satellites can be seen from the horizon to 15 degrees above the horizon. Check the following web site for satellite coverage in your area: http://corneroftheuniverse.net/orbcomm/sats/sat_coverage.html
Connect Caterpillar Electronic Technician (ET) to the machine. The ET connector is located on the control panel on the right side of the cab.
Turn the engine start switch to the ON position.
Open the ET software program.
Illustration 91 g01879234
ET will display a list of available electronic control modules. Select "Product Link". Press the "OK" button.
Illustration 92 g01879236
Select "Diagnostic Tests" from the "Diagnostics" menu. Select "Wiggle Test".
Illustration 93 g01879253
Read the warning that appears on the screen. Select the "OK" button.
Illustration 94 g01879255
Select the "Groups" button near the bottom right corner of the screen.
Illustration 95 g01879256
A new group for Product Link can be created by choosing the "New" button.
Illustration 96 g01879257
Type "Product Link". Select the "OK" button.
Illustration 97 g01879259
Available parameters and location of right arrow
In the left-hand column of available parameters, select "Number of GPS Satellites" under "Product Link". Then select the right arrow. In the left-hand column, select "Satellite Communications Status" under "Product Link". Select the right arrow.
Select the "OK" button.
Illustration 98 g01879260
Select "Product Link". Press the "OK" button.
Illustration 99 g01879262
confirm the two types of communication with the satellite, the "Number of GPS Satellites" should be at least one. The "Satellite Communication Status" should be "Established". The screen in Illustration98 shows that communication with GPS and the satellite is established. If the "Number of GPS Satellites" is at least one and "Satellite Communication Status" is "Established", the communication of Product Link is confirmed.If the "Number of GPS Satellites" is at least one and "Satellite Communication Status" is