3510814 SHAFT-DRIVE Caterpillar parts
M318D, M318D MH, M322D, M322D MH
Rating:
Alternative (cross code) number:
CA3510814
351-0814
3510814
CA3510814
351-0814
3510814
Weight: 0.65 pounds 0 kg.
WHEELED EXCAVATOR,
Number on catalog scheme:
1
For full view, you need register
Information:
Which Generate This Code:The CID 2803 diagnostic code that is activated by the Motor ECM is associated with a Motor ECM internal power supply. There is no procedure for checking the voltage of this internal power supply.The Motor ECM will activate the Motor, CID 2803 FMI 3 diagnostic code when the internal voltage of the power supply is above normal. The conditions that can cause the ECM to activate the Motor, CID 2803 FMI 3 diagnostic code are listed:
The Motor ECM has failed. Note: Ensure that the Motor, CID 2803 FMI 3 diagnostic code is active before performing this procedure.Test Step 1. SAFE SHUTDOWN PROCEDUREThis procedure must be performed before the service is performed in an area that is in the vicinity of power train hazardous voltage components and conductors in order to ensure that the DC power bus voltage and the DC accessory power bus voltage has discharged properly.ReferenceRefer to the Troubleshooting, "Electrical Maintenance Guidelines" section of this manual. Perform the "Safe Shutdown Procedure for Electric Drive Tractors" before proceeding with this procedure.Results:
OK - The Safe Shutdown Procedure for Electric Drive Tractors has been performed. The indication from the Hazardous Voltage Present Lamp and the Monitoring System Display are indicating that the DC system voltage has been properly discharged. Repair: The disconnect switch can be turned to the OFF position. The machine can now be serviced.This procedure should not require the disconnection of any of the hazardous voltage connectors. However, if an AC connection enclosure is opened or if a hazardous voltage DC connector is disconnected, a multimeter must be used to check for DC voltage between all of the exposed conductors and frame ground. Do not make personal contact with the exposed conductors until you have manually measured for voltage between ground and the conductors. Verify that there is less than 50.0 VDC present between the all exposed AC or DC hazardous voltage conductors and frame ground before any other action is taken. Proceed to the next troubleshooting test step.Test Step 2. FLASH THE LATEST SOFTWARE TO THE ECMIt is unlikely that the software program for the Motor ECM is causing this problem, however, flash the latest version of Motor ECM software to the ECM in order to eliminate this as a possible cause.
In order to flash the latest software to the Motor ECM, refer to the Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" procedure that is in this manual.
After completing the flash program procedure, return to this procedure and proceed to the next step.
After the latest version of Motor ECM software has been flashed to the Motor ECM, turn the key switch to the OFF position.
Start the engine. Run the engine at low idle.
Determine if the Motor, CID 2803 FMI 3 diagnostic code is active.Expected Result:The Motor, CID 2803 FMI 3 diagnostic code is not active. No new
The Motor ECM has failed. Note: Ensure that the Motor, CID 2803 FMI 3 diagnostic code is active before performing this procedure.Test Step 1. SAFE SHUTDOWN PROCEDUREThis procedure must be performed before the service is performed in an area that is in the vicinity of power train hazardous voltage components and conductors in order to ensure that the DC power bus voltage and the DC accessory power bus voltage has discharged properly.ReferenceRefer to the Troubleshooting, "Electrical Maintenance Guidelines" section of this manual. Perform the "Safe Shutdown Procedure for Electric Drive Tractors" before proceeding with this procedure.Results:
OK - The Safe Shutdown Procedure for Electric Drive Tractors has been performed. The indication from the Hazardous Voltage Present Lamp and the Monitoring System Display are indicating that the DC system voltage has been properly discharged. Repair: The disconnect switch can be turned to the OFF position. The machine can now be serviced.This procedure should not require the disconnection of any of the hazardous voltage connectors. However, if an AC connection enclosure is opened or if a hazardous voltage DC connector is disconnected, a multimeter must be used to check for DC voltage between all of the exposed conductors and frame ground. Do not make personal contact with the exposed conductors until you have manually measured for voltage between ground and the conductors. Verify that there is less than 50.0 VDC present between the all exposed AC or DC hazardous voltage conductors and frame ground before any other action is taken. Proceed to the next troubleshooting test step.Test Step 2. FLASH THE LATEST SOFTWARE TO THE ECMIt is unlikely that the software program for the Motor ECM is causing this problem, however, flash the latest version of Motor ECM software to the ECM in order to eliminate this as a possible cause.
In order to flash the latest software to the Motor ECM, refer to the Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program" procedure that is in this manual.
After completing the flash program procedure, return to this procedure and proceed to the next step.
After the latest version of Motor ECM software has been flashed to the Motor ECM, turn the key switch to the OFF position.
Start the engine. Run the engine at low idle.
Determine if the Motor, CID 2803 FMI 3 diagnostic code is active.Expected Result:The Motor, CID 2803 FMI 3 diagnostic code is not active. No new
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
2758159
SHAFT GP-MOTOR
M315D, M316D, M317D 2, M318D, M318D MH, M322D, M322D MH, M325D L MH, M325D MH, M330D
M315D, M316D, M317D 2, M318D, M318D MH, M322D, M322D MH, M325D L MH, M325D MH, M330D
3338042
SHAFT-AXLE
M315D, M316D, M317D 2, M318D, M318D MH
M315D, M316D, M317D 2, M318D, M318D MH
2676736
SHAFT-PINION
318E L, 319D, 319D L, 319D LN
318E L, 319D, 319D L, 319D LN
3640979
SHAFT
315D L, 316E L, 318D L
315D L, 316E L, 318D L
3481871
SHAFT
313D2 LGP, 315D L, 316E L, 318D L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D2, 320D2 GC, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D2 L, 325D, 329D ...
313D2 LGP, 315D L, 316E L, 318D L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D2, 320D2 GC, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D2 L, 325D, 329D ...
3054931
SHAFT AS-ROCKER ARM
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN
3689997
SHAFT-DRIVEN
311D LRR, 311F LRR, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 316E L, 318D L, 318D2 L, 318E L
311D LRR, 311F LRR, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 316E L, 318D L, 318D2 L, 318E L
3689996
SHAFT-DRIVE
311D LRR, 311F LRR, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 316E L, 318D L, 318D2 L, 318E L
311D LRR, 311F LRR, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 316E L, 318D L, 318D2 L, 318E L
2934313
SHAFT GP-HYDRAULIC MOTOR
M313D, M315D 2
M313D, M315D 2
3338040
SHAFT-AXLE
M313D, M315D 2
M313D, M315D 2
3219007
SHAFT
M318D MH, M322D, M322D MH
M318D MH, M322D, M322D MH
320B FM LL, 320C FM, 325B L, 325C, 325C L, 325D MH, 330B L, 330C L, 330C MH, 330D MH, 345B, 345B II, 345B II MH, 345C, 345C MH, 350 L, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M318D MH, M322D MH, M...