4507504 SHAFT AS-AXLE Caterpillar parts
795F AC, 795F XQ
Rating:
Alternative (cross code) number:
CA4507504
450-7504
4507504
CA4507504
450-7504
4507504
Weight: 274 pounds 124 kg.
TRUCK,
Information:
Assembly Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-9901     Hydraulic Cylinder Repair Stand     1    
3S-6224 Hydraulic Pump     1    
B     8T-5245     Torque Multiplier     1    
1P-0851 Spline Adapter     1    
1P-0852 Male Adapter     1    
5P-1748 Impact Socket (2 1/4 inch)     1    
C     3S-6224     Hydraulic Pump     1    
6V-3160 Hydraulic Puller     1    
5F-7366 Forcing Screw (1 inch by 14 by 13 1/4 inch)     1    
1P-1835 Adapter     1    
1A-1935 Nut (1 inch by 14)     1    
3K-5234 Washer (1 inch)     1    ReferenceRefer to Specifications, "Ripper Tilt Cylinder" for additional information.
Inspect the O-ring seals for wear and for damage. Replace the components with new components, if necessary. Make sure that the components are clean. Apply clean oil to the surfaces of the components during assembly.
Illustration 1 g00828998
Lower the temperature of sleeve bearings (15) and (16) . Use Tooling (C) to install the sleeve bearings in the eyes of the cylinder rod and of the ripper cylinder. The sleeve bearings must be installed even with the bottom surfaces of the counterbores. The correct inner diameter of both bearings after assembly is 76.233 0.083 mm (3.001 0.003 inch).
Install wear ring (11) in cylinder head (3) . Install seals (12) , (13) and (14) in head (3) . Apply clean oil to the lips of the seals.
Install backup ring (10) and install O-ring seal (9) on head (3) .
Install wear ring (7) and install seal (8) on piston (6) .
Install piston (6) on cylinder rod (1) .
Apply clean oil to the threads on the end of cylinder rod (1) . Install nut (5) and the washer. Use Tooling (B) in order to tighten nut (5) to a torque of 2700 270 N m (1991 199 lb ft).
Use Tooling (A) to push ripper cylinder (4) onto cylinder rod (1) . Install bolts (2) and the washers that fasten cylinder head (3) to the ripper cylinder. Tighten bolts (2) to a torque of 620 80 N m (460 60 lb ft).
Remove the ripper cylinder from Tooling (A) . The weight of the ripper cylinder is approximately 120 kg (260 lb).End By: Install the ripper tilt cylinder on the machine. Refer to Disassembly and Assembly, "Ripper Tilt Cylinder - Install".
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-9901     Hydraulic Cylinder Repair Stand     1    
3S-6224 Hydraulic Pump     1    
B     8T-5245     Torque Multiplier     1    
1P-0851 Spline Adapter     1    
1P-0852 Male Adapter     1    
5P-1748 Impact Socket (2 1/4 inch)     1    
C     3S-6224     Hydraulic Pump     1    
6V-3160 Hydraulic Puller     1    
5F-7366 Forcing Screw (1 inch by 14 by 13 1/4 inch)     1    
1P-1835 Adapter     1    
1A-1935 Nut (1 inch by 14)     1    
3K-5234 Washer (1 inch)     1    ReferenceRefer to Specifications, "Ripper Tilt Cylinder" for additional information.
Inspect the O-ring seals for wear and for damage. Replace the components with new components, if necessary. Make sure that the components are clean. Apply clean oil to the surfaces of the components during assembly.
Illustration 1 g00828998
Lower the temperature of sleeve bearings (15) and (16) . Use Tooling (C) to install the sleeve bearings in the eyes of the cylinder rod and of the ripper cylinder. The sleeve bearings must be installed even with the bottom surfaces of the counterbores. The correct inner diameter of both bearings after assembly is 76.233 0.083 mm (3.001 0.003 inch).
Install wear ring (11) in cylinder head (3) . Install seals (12) , (13) and (14) in head (3) . Apply clean oil to the lips of the seals.
Install backup ring (10) and install O-ring seal (9) on head (3) .
Install wear ring (7) and install seal (8) on piston (6) .
Install piston (6) on cylinder rod (1) .
Apply clean oil to the threads on the end of cylinder rod (1) . Install nut (5) and the washer. Use Tooling (B) in order to tighten nut (5) to a torque of 2700 270 N m (1991 199 lb ft).
Use Tooling (A) to push ripper cylinder (4) onto cylinder rod (1) . Install bolts (2) and the washers that fasten cylinder head (3) to the ripper cylinder. Tighten bolts (2) to a torque of 620 80 N m (460 60 lb ft).
Remove the ripper cylinder from Tooling (A) . The weight of the ripper cylinder is approximately 120 kg (260 lb).End By: Install the ripper tilt cylinder on the machine. Refer to Disassembly and Assembly, "Ripper Tilt Cylinder - Install".
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
4M1854
SHAFT-LEVER
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
2128180
SHAFT AS-PUMP DRIVE
3406B, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 79...
3406B, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 79...
2896329
SHAFT AS
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ
4308140
SHAFT-IDLER
793F, 793F CMD, 793F OEM, 795F AC, 795F XQ
793F, 793F CMD, 793F OEM, 795F AC, 795F XQ
2836705
SHAFT-OUTPUT
793F AC, 795F AC
793F AC, 795F AC
4243469
SHAFT-OUTPUT
795F AC, 795F XQ
795F AC, 795F XQ
3926516
SHAFT-AXLE
795F AC
795F AC
4289377
SHAFT-AXLE
795F AC
795F AC
2974874
SHAFT
795F AC, 795F XQ
795F AC, 795F XQ
3020379
SHAFT
795F AC, 795F XQ
795F AC, 795F XQ
3087310
SHAFT AS
795F AC, 795F XQ
795F AC, 795F XQ
3087316
SHAFT AS-DRIVE
795F AC, 795F XQ
795F AC, 795F XQ
4289377
SHAFT-AXLE
795F AC
795F AC
3926516
SHAFT-AXLE
795F AC
795F AC
4243469
SHAFT-OUTPUT
795F AC, 795F XQ
795F AC, 795F XQ
2836705
SHAFT-OUTPUT
793F AC, 795F AC
793F AC, 795F AC
3572122
SHAFT
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
3083243
SHAFT-AXLE
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
4339477
SHAFT
777G, 785D
777G, 785D
3087316
SHAFT AS-DRIVE
795F AC, 795F XQ
795F AC, 795F XQ
3087310
SHAFT AS
795F AC, 795F XQ
795F AC, 795F XQ
3020379
SHAFT
795F AC, 795F XQ
795F AC, 795F XQ
2974874
SHAFT
795F AC, 795F XQ
795F AC, 795F XQ