4D6837 SHAFT Caterpillar parts
12E, 140B
Rating:
Alternative (cross code) number:
CA4D6837
4D-6837
4D6837
CA4D6837
4D-6837
4D6837
Weight: 1 pounds 0 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$128.75
09 Jun 2022
Amazon.com
CTP 4D6837 Shaft for Hydraulic Vane Pump
CTP For Hydraulic Vane Pump || Highly Efficient || Easy in-and-out fit
CTP For Hydraulic Vane Pump || Highly Efficient || Easy in-and-out fit
$122.10
09 Jun 2022
US: Florida-Parts-Z
4D6837 - Shaft for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$134.57
09 Jun 2022
1.3007[0.59] Pounds
US: ProperBuy
4D6837 Shaft Fits Caterpillar
TCP Warranty
TCP Warranty
Number on catalog scheme:
19
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Illustration 1 g03466763
Cut cable straps (4) from wiring harness assembly (3). Note: Note the position of cable straps that attach the wiring harness assembly to the ECM mounting bracket.
Remove bolt (7) from bracket (4) for plastic tube assembly. Position the bracket away from ECM mounting bracket (1).
Slide locking tab into the unlocked position. Disconnect wiring harness (5) from atmospheric pressure sensor (6) (not shown).
Remove bolts (2) from ECM mounting bracket (1).
Remove ECM mounting bracket (1) from the cylinder block.
If necessary, remove atmospheric pressure sensor (6) (not shown) from the ECM mounting bracket. Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 2 g03466763
Ensure that ECM mounting bracket (1) for the electronic control module is clean and free from damage. If the mounting bracket is damaged, replace the bracket.
If necessary, install atmospheric pressure sensor (6) (not shown) to ECM mounting bracket (1). Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure.
Position ECM mounting bracket (1) onto the cylinder block.
Install bolts (2) to ECM mounting bracket (1). Tighten the bolts to a torque of 22 N m (195 lb in).
Connect harness assembly (5) to atmospheric pressure sensor (6) (not shown). Slide the locking tab into the locked position.
Position bracket (4) for plastic tube assembly onto ECM mounting bracket (1). Install bolt (7) to the bracket for plastic tube assembly. Tighten the bolt to a torque of 22 N m (195 lb in)
Install new cable straps (4) to wiring harness assembly (3). Note: Ensure that the cable straps meet the Original Equipment Manufactures (OEM) specifications.End By:
Install the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Start By:
Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Illustration 1 g03466763
Cut cable straps (4) from wiring harness assembly (3). Note: Note the position of cable straps that attach the wiring harness assembly to the ECM mounting bracket.
Remove bolt (7) from bracket (4) for plastic tube assembly. Position the bracket away from ECM mounting bracket (1).
Slide locking tab into the unlocked position. Disconnect wiring harness (5) from atmospheric pressure sensor (6) (not shown).
Remove bolts (2) from ECM mounting bracket (1).
Remove ECM mounting bracket (1) from the cylinder block.
If necessary, remove atmospheric pressure sensor (6) (not shown) from the ECM mounting bracket. Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 2 g03466763
Ensure that ECM mounting bracket (1) for the electronic control module is clean and free from damage. If the mounting bracket is damaged, replace the bracket.
If necessary, install atmospheric pressure sensor (6) (not shown) to ECM mounting bracket (1). Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure.
Position ECM mounting bracket (1) onto the cylinder block.
Install bolts (2) to ECM mounting bracket (1). Tighten the bolts to a torque of 22 N m (195 lb in).
Connect harness assembly (5) to atmospheric pressure sensor (6) (not shown). Slide the locking tab into the locked position.
Position bracket (4) for plastic tube assembly onto ECM mounting bracket (1). Install bolt (7) to the bracket for plastic tube assembly. Tighten the bolt to a torque of 22 N m (195 lb in)
Install new cable straps (4) to wiring harness assembly (3). Note: Ensure that the cable straps meet the Original Equipment Manufactures (OEM) specifications.End By:
Install the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
120G, 140B, 1673C, 235, 3304, 3306, 3306B, 528, 814, 815B, 920, 930, 941, 955L, 966C, D4E, D5B, D7G, G3304, G3306
12E, 16, 1693, 583H, 621, 641B, 651, 657, 666, 772, 777, 955C, 977H, 988, 992, D10, D315, D320A, D326F, D337, D342, D342C, D343, D348, D353C, D375D, D379A, D398, D399, D8H, D9E, D9G, D9H
12E, 1673, 1673B, 1673C, 955H, D320A, D330A, D330B, D333A, D4D
120G, 12G, 140B, 140G, 14G, 1673C, 215, 225, 235, 3304, 3306, 518, 627B, 637D, 941, 950, 955L, D4D, D4E, D5, D5B, D6C, D6D, D7F, D7G
12E, 977H, D4D
120B, 12E, 140, 140B
120, 120B, 120G, 12E, 12F, 12G, 130G, 140, 140B, 140G, 14E
120B, 12E, 140, 140B
120B, 12E, 12F, 140, 140B, 14E
120, 120B, 12E, 140, 140B, 14E
120B, 140B
120, 120B, 140, 140B
4D3558
SHAFT AS
140B
140B
5H3351
SHAFT
12E
12E
140B
2Y7194
SHAFT
140B
140B
2Y7195
SHAFT AS
140B
140B
2Y7192
SHAFT
140B
140B
12E
2Y2451
SHAFT
120B
120B
2Y2352
SHAFT AS
120B
120B