AVSPARE.COM
parts catalog

SHAFT-PULLEY 5088195 - Caterpillar



5088195 SHAFT-PULLEY Caterpillar parts SHAFT
Rating:
46
Alternative (cross code) number:
CA5088195
508-8195
5088195
Caterpillar 5088195 SHAFT-PULLEY
Weight: 28 pounds 12 kg.

Buy SHAFT-PULLEY 5088195 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 4
 
  For full view, you need register

Information:

Removal Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01391246
Disconnect sensor harness assembly (1) from the engine harness assembly.
Illustration 2 g01391288
Remove cable straps (5) that secure the harness assemblies to the support clips.
Remove nut (2) and sensor (3) from mounting ring (4).
Remove bolts (6), the washers, the spacers, and the rubber mounts.
Remove sensor control unit (8) and bracket assembly (7).
Illustration 3 g01391302
Remove nuts (9) and the washers.
Remove cover (10) and the spacers.
Illustration 4 g01391315
Remove sensor assembly (11). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 5 g01391315
Install new sensor assembly (11).
Illustration 6 g01391302
Install the spacers and cover (10).
Install the washers and nuts (9) and hand tighten nuts (9).
Tighten nuts (9) to a torque of 25 6 N m (18 4 lb ft).
Illustration 7 g01391288
Position bracket (7) and sensor control unit (8).
Install the rubber mounts, the spacers, the washers, and bolts (6).
Install sensor (3) into mounting ring (4) and tighten nut (2) to a torque of 50 5 N m (37 4 lb ft).
Install cable straps (5) in order to secure the harness assembly to the support clips. Note: Secure the harness assembly to the upper support with the tie so that there is 135 mm (5.0 inch) of slack between the sensor and the support clip.Note: Secure the harness assembly to the lower support with the tie so that there is 110 mm (4.0 inch) of slack between the edge of the cover for the sensor control unit and the first support clip.
Illustration 8 g01391246
Connect sensor harness assembly (1) to the engine harness assembly.

Caterpillar parts catalog:

Caterpillar parts catalog
PM310 Cold Planer RH800001-UP (MACHINE) POWERED BY C9.3 Engine
PM310 Cold Planer NM900001-UP (MACHINE) POWERED BY C9.3 Engine
PM312 Cold Planer LJ900001-UP (MACHINE) POWERED BY C9.3 Engine
PM312 Cold Planer NJX00001-UP (MACHINE) POWERED BY C9.3 Engine
PM313 Cold Planer J6300001-UP (MACHINE) POWERED BY C9.3 Engine
PM313 Cold Planer JHZ00001-UP (MACHINE) POWERED BY C9.3 Engine
PM312 Cold Planer NA900001-UP (MACHINE) POWERED BY C9 Engine
PM313 Cold Planer DK900001-UP (MACHINE) POWERED BY C9 Engine
PM312 Cold Planer NJ900001-UP (MACHINE) POWERED BY C9 Engine
PM313 Cold Planer JH900001-UP (MACHINE) POWERED BY C9 Engine
PM310 Cold Planer NMA00001-UP (MACHINE) POWERED BY C9 Engine
PM310 Cold Planer KWA00001-UP (MACHINE) POWERED BY C9 Engine


Parts shaft Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.