5365535 SHAFT-DRIVE Caterpillar parts
Rating:
Alternative (cross code) number:
CA5365535
536-5535
5365535
CA5365535
536-5535
5365535
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5472 Lifting Eye Assembly 2
B FT-3307 Installation Tool 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06238979Note: Note the position of the wiring harness clips.
If necessary, remove housing (7).
Illustration 2 g06238900
Install Tooling (B) and a suitable lifting device to torque converter (6). The weight of torque converter (6) is approximately 109 kg (240 lb).Note: The torque converter needs to make three spline connections and spin freely to be properly seated.
Install torque converter (6) Remove the suitable lifting device and Tooling (A).
Position a new gasket and reinstall housing (7).
Illustration 3 g06238879
Install retaining ring (5).
Illustration 4 g06238867Note: Install a new retaining ring (3) Do not reuse old retaining ring (3).
Install plate (4). Install retaining ring (3).
Illustration 5 g06239001Note: Typical Example.
Illustration 6 g06239011Note: Typical Example.
Install the O-ring seals onto pilot (2). Using Tooling (B) install pilot (2). Install retaining ring (1).End By:
Install the transmission.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5472 Lifting Eye Assembly 2
B FT-3307 Installation Tool 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06238979Note: Note the position of the wiring harness clips.
If necessary, remove housing (7).
Illustration 2 g06238900
Install Tooling (B) and a suitable lifting device to torque converter (6). The weight of torque converter (6) is approximately 109 kg (240 lb).Note: The torque converter needs to make three spline connections and spin freely to be properly seated.
Install torque converter (6) Remove the suitable lifting device and Tooling (A).
Position a new gasket and reinstall housing (7).
Illustration 3 g06238879
Install retaining ring (5).
Illustration 4 g06238867Note: Install a new retaining ring (3) Do not reuse old retaining ring (3).
Install plate (4). Install retaining ring (3).
Illustration 5 g06239001Note: Typical Example.
Illustration 6 g06239011Note: Typical Example.
Install the O-ring seals onto pilot (2). Using Tooling (B) install pilot (2). Install retaining ring (1).End By:
Install the transmission.
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
5280601
SHAFT
Caterpillar
Caterpillar
5216856
SHAFT-SEAL
Caterpillar
Caterpillar
5213695
SHAFT AS-TRACK CARRIER ROLLER
Caterpillar
Caterpillar
5171545
SHAFT & PINION
Caterpillar
Caterpillar
5171086
SHAFT-GEAR
Caterpillar
Caterpillar
5095777
SHAFT
Caterpillar
Caterpillar
3564202
SHAFT-BEVEL PINION
Caterpillar
Caterpillar
3315207
SHAFT-WATER PUMP
Caterpillar
Caterpillar
5594160
SHAFT
Caterpillar
Caterpillar
5594148
SHAFT
Caterpillar
Caterpillar
5575652
SHAFT
Caterpillar
Caterpillar
5507773
SHAFT AS
Caterpillar
Caterpillar