SHAFT-IDLER 5652046 - Caterpillar

5652046 SHAFT-IDLER Caterpillar parts

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA5652046
565-2046
5652046

Buy SHAFT-IDLER 5652046 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 5

Caterpillar 5652046 Parts scheme SHAFT-IDLER

For full view, you need register

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

352F Excavator WYA00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » M00978210373

349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » M00709020579

352F Excavator RBF00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » M00813440445

349 Excavator LKG00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » M01017690495

352 Excavator MGR00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » M01017790499

349 Excavator RBY00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » M01017930398
575-6593: IDLER GP-FRONT » M01017930401

349F L Excavator KEA00001-UP (MACHINE) POWERED BY C13 Engine

561-8970: IDLER GP-FRONT » SEBP65470747

Information:

Table 1
Required Tools
Part Number Description Qty
FT-2542 Track block assembly 1
Container for measuring 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Illustration 1 g00714531
Sprocket (left track) (1) Sprocket (2) FT-2542 Track block assembly
Place track block assembly (2) in sprocket (1) in order to block forward left travel.
Illustration 2 g00767002
(3) Case drain hose
Disconnect the case drain hose (3) from the connector at the swing motor. Place the open end of the case drain hose (3) into the container for measuring.
Install 6V-9830 Cap on tee (2) of the swivel.
Start the engine.
Place the engine speed dial at position "10" and AEC switch OFF. Maintain the maximum no-load speed at 2050 50 rpm.ReferenceRefer to Testing and Adjusting, "Engine Performance - Test" for engine rpm settings.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Move the left travel lever forward fully for one minute.
Measure the amount of case drain oil.
Remove track block assembly (2) from sprocket (1) .
Move the left travel lever in order to reposition the travel motor.
Place track block assembly (2) in sprocket (1) in order to block forward left travel.
Repeat Steps 9 through 13 in order to obtain three measurements of case drain oil.The following values specify the maximum acceptable flow of case drain oil when the travel crossover relief valves are set at 36800 1470 kPa (5350 215 psi). New travel motor ... 15 L/min (4.0 US gpm) Rebuilt travel motor ... 18 L/min (4.8 US gpm)