AVSPARE.COM
parts catalog

SHAFT 6K8295 - Caterpillar


6K8295 SHAFT Caterpillar parts 518, 930
Rating:
75
Alternative (cross code) number:
CA6K8295
6K-8295
6K8295
Caterpillar 6K8295 SHAFT
Weight: 0.11 pounds 0 kg.

Buy SHAFT 6K8295 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER, WHEEL SKIDDER,

Compatible equipment models: 6K8295:

WHEEL LOADER  930  
WHEEL SKIDDER  518   Caterpillar
Number on catalog scheme: None
  For full view, you need register

Information:

Powering the electronic control system on a dedicated fused circuit will reduce the possibility of degraded electronic control system performance due to voltage transients. Additional loads should not be connected between the ECM and ECM circuit protection. Refer to Schematic and Installation Section (in this manual) for information regarding required connections.The ECM switched battery connection is made to Customer Connector P3 pin-26. To prevent engine shutdown in the event of a short circuit in the vessel harness, the control system must be powered on a dedicated protected circuit. The wire size should be #14 AWG. This connection should be made through switched battery so it will be powered when the keyswitch (or engine control switch) is in the OFF position.Circuit protection for this circuit must be 15 Amps (for 12V or 24V system) and rated for a continuous duty load of 8.0 Amperes at 12 VDC (5.0 Amperes at 24 VDC). DO NOT use in-line fuses for circuit protection. Caterpillar prefers using circuit breakers for circuit protection. Circuit breakers should be located with other vessel circuit protection in a centrally located, dedicated panel.If automatically resetting circuit breakers are used, consideration of the breaker location environment and its effect on the trip point is critical. The trip point of some circuit breakers can be significantly reduced below the rated trip point if exposed to high temperatures. This can cause intermittent shutdowns resulting in incorrectly replaced engine electronic components.An ECM diagnostic strategy monitors ECM battery voltage, and is triggered if the voltage to the ECM drops below 83% of the system voltage.Operation in 24 Volt Systems
The Marine Engine can operate in 24 VDC electrical systems with circuit protection. The specification is the same as for 12 VDC systems and continuous duty load is 5.0 Amperes at 24 VDC.

Caterpillar parts catalog:

Caterpillar parts catalog
930 WHEEL LOADER 41K00001-03207 (MACHINE)
930 WHEEL LOADER 79J00001-02223 (MACHINE)
930 WHEEL LOADER 41K00001-03207 (MACHINE)
930 WHEEL LOADER 79J00001-02223 (MACHINE)
518 SKIDDER 50S00001-00596 (MACHINE)
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 79J00001-02223 (MACHINE)
930 WHEEL LOADER 79J02224-03732 (MACHINE)
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 79J00001-02223 (MACHINE)
930 WHEEL LOADER 79J02224-03732 (MACHINE)
930 WHEEL LOADER 41K00001-03207 (MACHINE)
930 WHEEL LOADER 41K03208-05314 (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 71H00001-00259 (MACHINE)
930 WHEEL LOADER 41K00001-03207 (MACHINE)
930 WHEEL LOADER 41K03208-05314 (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 79J00001-02223 (MACHINE)
930 WHEEL LOADER 79J02224-03732 (MACHINE)
930 WHEEL LOADER 79J00001-02223 (MACHINE)
930 WHEEL LOADER 79J02224-03732 (MACHINE)
518 SKIDDER 50S00001-00596 (MACHINE)
518 SKIDDER 50S00597-01288 (MACHINE)
518 SKIDDER 50S01289-03229 (MACHINE) POWERED BY 3304 ENGINE
518 SKIDDER 50S00597-01288 (MACHINE)
518 SKIDDER 50S01289-03229 (MACHINE) POWERED BY 3304 ENGINE
518 SKIDDER 50S00597-01288 (MACHINE)
518 SKIDDER 50S00001-00596 (MACHINE)
518 SKIDDER 50S00597-01288 (MACHINE)
518 SKIDDER 50S01289-03229 (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 41K03208-05314 (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 71H00001-00259 (MACHINE)
930 WHEEL LOADER 71H00260-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 41K03208-05314 (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 71H00001-00259 (MACHINE)
930 WHEEL LOADER 71H00260-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 73U00352-01312 (MACHINE) POWERED BY 3304 ENGINE


Parts shaft Caterpillar catalog:

4M1854 SHAFT-LEVER
1090, 1140, 1150, 1160, 1190, 1190T, 120M, 120M 2, 1290T, 12E, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1673, 1673B,...
7N5899 SHAFT-WATER PUMP
120G, 140B, 1673C, 235, 3304, 3306, 3306B, 528, 814, 815B, 920, 930, 941, 955L, 966C, D4E, D5B, D7G, G3304, G3306
8H9804 SHAFT-PUMP IDLER
120G, 12E, 12G, 140B, 140G, 14G, 1673, 1673C, 1676, 215, 225, 235, 3160, 3208, 3304, 3306, 3408, 3412, 518, 613B, 613C, 627B, 637D, 650B, 651E, 657E, 941, 950, 955L, 977H, 988B, 992, 992C, CS-551, D33...
4S8670 SHAFT-PLANETARY
14G, 14H, 14H NA, 16G, 16H, 16H NA, 518, 518C, 528, 528B, 530B, 578, 583R, 589, 920, 930, 941, 951B, D4D, D4E
3S9930 SHAFT
518, 518C, 528, 528B, 530B, 613, 613B, 920, 930, 941, 951B, D4D, FB518
3S7987 SHAFT
518, 518C, 528, 528B, 530B, 920, 930, 941, 951B, D4D, D4E
7K1871 SHAFT
920, 930, 930R
6K2034 SHAFT
508, 518, 518C, 528, 528B, 530B, 920, 930, 930R, 950, 966C, 966R, 980B, FB518
2V5608 SHAFT
518, 930, 930R
8K6769 SHAFT ASSEM.
518, 528, 814, 920, 930, 950, 966C, 980B, 988, 992
7K1871 SHAFT
920, 930, 930R
5J3162 SHAFT
621, 623, 631C, 633C
3S8038 SHAFT
627, 980, 980B
6K7597 SHAFT
920, 930, 930R
6K8164 SHAFT
920, 930, 930R
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.