6T8703 SHAFT AS Caterpillar parts
120G, 12G, 130G, 140G
Rating:
Alternative (cross code) number:
CA6T8703
6T-8703
6T8703
CA6T8703
6T-8703
6T8703
Weight: 9 pounds 4 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
Use this procedure in order to troubleshoot an engine shutdown or use this procedure if one of the following event codes is active. Refer to Troubleshooting, "Diagnostic Trouble Codes" for information about these events. Access the engine monitoring system on Caterpillar Electronic Technician (ET) in order to view the current trip points for these codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring Parameters".
Table 1
Diagnostic Trouble Code
Code and Description Conditions which Activate the Code System Response
3607-31 Engine Emergency Shutdown Indication The engine is in the run mode or the cooldown mode and an emergency stop shutdown has been initiated. The code is logged.
The gas shutoff valve, the fuel actuator, and the ignition to the engine is disabled.
The red stop lamp is activated.
The engine is shut down.
5272-31 Unexpected Engine Shutdown The engine is in the run mode and the engine speed drops below the 100 rpm. The code is logged.
The red stop lamp is activated.
The engine is shut down.
This engine event is latched.(1)
(1) The engine control switch must be cycled to the OFF position prior to restarting the engine.
Unburned gas in the air inlet and exhaust system may ignite when the engine is started. Personal injury and/or property damage may result.Before starting an engine that may contain unburned gas, purge the unburned gas from the air inlet and exhaust system. Refer to the topic on purging unburned gas in the "Starting the Engine" section.
The ignition is immediately terminated when an emergency stop button is pressed. Unburned gas remains in the air inlet and exhaust system.Probable Causes for a 3607-31
Emergency shutdown that is initiated by the operator
Faulty circuit for the emergency stop switch
Faulty emergency shutdown switchProbable Causes for a 5272-31
Engine overload
Excessive load at start-up
Faulty fuel shutoff valve
Incorrect mode switch inputs
Starting motor relay
Incorrect settings for the system configuration parametersRecommended Actions for a 3607-31 Code
Faulty Circuit for the Emergency Stop
Note: The circuit for the emergency stop circuit must remain grounded in order for the engine to run.Inspect the wiring between the emergency shutdown switch and the connector at the Electronic Control Module (ECM). Look for damage and/or corrosion. Refer to Testing and Adjusting, "Electrical Connectors - Inspect" for information that is related to the diagnosis of intermittent conditions in the harness wiring and/or connectors.Faulty Emergency Shutdown Switch
Inspect the emergency shutdown switch for evidence of damage that has been caused by vibration. Disassemble the switch. Inspect the components for looseness, for cracks, and for abrasion. Use an ohmmeter and toggle the switches in order to check for proper electrical operation.Replace any faulty components.Recommended Actions for a 5272-31 Code
Engine Overload
Check the driven equipment for the reason for the overload. Ensure that the problem has been corrected. Reset the control system. Resume normal operation.Excessive Load at Start-up
Ensure that the engine is cranking at an adequate speed during starting.Check that the load is not excessive during starting. Reduce the load. If necessary, disengage the driven equipment and test the engine.Check for a problem with the parasitic loads that are on the engine. Check
Table 1
Diagnostic Trouble Code
Code and Description Conditions which Activate the Code System Response
3607-31 Engine Emergency Shutdown Indication The engine is in the run mode or the cooldown mode and an emergency stop shutdown has been initiated. The code is logged.
The gas shutoff valve, the fuel actuator, and the ignition to the engine is disabled.
The red stop lamp is activated.
The engine is shut down.
5272-31 Unexpected Engine Shutdown The engine is in the run mode and the engine speed drops below the 100 rpm. The code is logged.
The red stop lamp is activated.
The engine is shut down.
This engine event is latched.(1)
(1) The engine control switch must be cycled to the OFF position prior to restarting the engine.
Unburned gas in the air inlet and exhaust system may ignite when the engine is started. Personal injury and/or property damage may result.Before starting an engine that may contain unburned gas, purge the unburned gas from the air inlet and exhaust system. Refer to the topic on purging unburned gas in the "Starting the Engine" section.
The ignition is immediately terminated when an emergency stop button is pressed. Unburned gas remains in the air inlet and exhaust system.Probable Causes for a 3607-31
Emergency shutdown that is initiated by the operator
Faulty circuit for the emergency stop switch
Faulty emergency shutdown switchProbable Causes for a 5272-31
Engine overload
Excessive load at start-up
Faulty fuel shutoff valve
Incorrect mode switch inputs
Starting motor relay
Incorrect settings for the system configuration parametersRecommended Actions for a 3607-31 Code
Faulty Circuit for the Emergency Stop
Note: The circuit for the emergency stop circuit must remain grounded in order for the engine to run.Inspect the wiring between the emergency shutdown switch and the connector at the Electronic Control Module (ECM). Look for damage and/or corrosion. Refer to Testing and Adjusting, "Electrical Connectors - Inspect" for information that is related to the diagnosis of intermittent conditions in the harness wiring and/or connectors.Faulty Emergency Shutdown Switch
Inspect the emergency shutdown switch for evidence of damage that has been caused by vibration. Disassemble the switch. Inspect the components for looseness, for cracks, and for abrasion. Use an ohmmeter and toggle the switches in order to check for proper electrical operation.Replace any faulty components.Recommended Actions for a 5272-31 Code
Engine Overload
Check the driven equipment for the reason for the overload. Ensure that the problem has been corrected. Reset the control system. Resume normal operation.Excessive Load at Start-up
Ensure that the engine is cranking at an adequate speed during starting.Check that the load is not excessive during starting. Reduce the load. If necessary, disengage the driven equipment and test the engine.Check for a problem with the parasitic loads that are on the engine. Check
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
6G5532
SHAFT-DRIVE PINION
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H, 163H NA
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H, 163H NA
1067131
SHAFT
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA
6E1861
SHAFT-PUMP
12G, 130G, 140G, 160G
12G, 130G, 140G, 160G
9T7783
SHAFT
12G, 130G, 140G, 160G
12G, 130G, 140G, 160G
1095562
SHAFT
12G, 130G, 140G, 160G
12G, 130G, 140G, 160G
1267130
SHAFT AS
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
6E5885
SHAFT
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 24H
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 24H
8X7956
SHAFT AS
120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
1078375
SHAFT AS
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
1022385
SHAFT-PUMP
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K
1533580
SHAFT
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160K
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160K
7B5036
SHAFT
120, 120B, 120G, 12E, 12F, 12G, 130G, 140, 140B, 140G, 14E
120, 120B, 120G, 12E, 12F, 12G, 130G, 140, 140B, 140G, 14E
9P8456
SHAFT AS
120G, 130G
120G, 130G
5S7945
SHAFT AS-PLANETARY
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3P0297
SHAFT AS
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3P0726
SHAFT AS
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3P0754
SHAFT AS-IDLER
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
3P3424
SHAFT
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
4T3197
SHAFT
120G, 12G, 130G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 160G, 16G
9T8056
SHAFT-GOVERNOR CONTROL
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
8D7427
SHAFT-DRIVE PINION
120G, 12G, 130G, 140G, 160G
120G, 12G, 130G, 140G, 160G
8D6841
SHAFT
120G, 12G, 130G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 160G, 16G
6Y0299
SHAFT AS
120G, 12G, 130G, 140G
120G, 12G, 130G, 140G