6T9204 SHAFT Caterpillar parts
D7H, D7R, D7R II
Rating:
Alternative (cross code) number:
CA6T9204
6T-9204
6T9204
CA6T9204
6T-9204
6T9204
Weight: 906 pounds 411 kg.
TRACK-TYPE TRACTOR,
Related part:
6T9204
SHAFT-PIVOT
10R9165
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 6T9204 Pivot Shaft for Model D7H/D7R/D7R II
CTP For Model D7H/D7R/D7R II || Sold in each || Easy in-and-out fit
CTP For Model D7H/D7R/D7R II || Sold in each || Easy in-and-out fit
CTP 6T9204 Pivot Shaft for Model D7H/D7R/D7R II
CTP For Model D7H/D7R/D7R II || Sold in each || Easy in-and-out fit
CTP For Model D7H/D7R/D7R II || Sold in each || Easy in-and-out fit
Number on catalog scheme:
8
For full view, you need register
Information:
All Caterpillar Engines Equipped With A TurbochargerBe sure to correctly tighten the clamp assemblies that fasten the compressor housing and turbine housing to the cartridge. If a clamp assembly becomes loose, a housing may contact the compressor wheel or turbine wheel. This could result in damage to the turbocharger components. Use the procedure that follows to install the clamp assemblies. Make a note of this procedure in the appropriate Service Manual Disassembly and Assembly modules.
1. Be sure the clamp assemblies are correctly located on the housings and the cartridge. Be sure the housings are correctly oriented on the cartridge. Then tighten each clamp assembly nut or bolt to the specified torque.2. Lightly tap all around the outside of each clamp assembly with a soft hammer to be sure it is seated.3. Again, tighten each clamp assembly nut or bolt to the specified torque.4. Repeat Steps 2 and 3 until each clamp assembly nut or bolt does not turn when the specified torque is applied.
Location of clamp assemblies.
1. Be sure the clamp assemblies are correctly located on the housings and the cartridge. Be sure the housings are correctly oriented on the cartridge. Then tighten each clamp assembly nut or bolt to the specified torque.2. Lightly tap all around the outside of each clamp assembly with a soft hammer to be sure it is seated.3. Again, tighten each clamp assembly nut or bolt to the specified torque.4. Repeat Steps 2 and 3 until each clamp assembly nut or bolt does not turn when the specified torque is applied.
Location of clamp assemblies.
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
578, 583R, 587R, D7H, D8N, D8R
578, D7H, D8N
561M, 572R, D10, D10N, D11N, D5H, D5H XL, D5M, D6E, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6M, D6R, D7G, D7G2, D7H, D7R, D8L, D8N, D8R, D9L, D9N, D9R
D6H, D6H XL, D6H XR, D7H
814B, 815B, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, D6H, D6H XL, D6H XR, D7H, D8N
572R II, 583R, 583T, 587R, 587T, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R II, D7R XR, D8R, D8R II, D8T, PL83, PL87
572R, 572R II, 583R, 587R, 587T, D6R, D6R II, D7R, D7R II, PL87
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
572R II, D7R II, D8R II
D7H, D8N
D7H, D7R
D7R
9T5705
SHAFT
953
953
8E3520
SHAFT ASSEM. (L. H.)
D7H, D7R, D7R II, D7R XR
D7H, D7R, D7R II, D7R XR
6I8106
SHAFT
D7H
D7H
6G5127
SHAFT
D5H
D5H
5M5216
SHAFT ASSEM.
572G
572G