7G6952 SHAFT AS-OUTPUT Caterpillar parts
936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966R, G936, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
Rating:
Alternative (cross code) number:
CA7G6952
7G-6952
7G6952
CA7G6952
7G-6952
7G6952
Weight: 11 pounds 5 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Related part:
7G6952
SHAFT AS-YM
5241295
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$258.75
13 Apr 2022
US: Florida-Parts-Z
7G6952 - Shaft AS-Output fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 7G6952:
Information:
Remove Carburetor
1. Shut off gas supply line to gas pressure regulator. 2. Loosen clamps (1) and slide hose away from the carburetor.3. Disconnect control rod (2) from the carburetor lever. 4. Remove clamp (3) from the joint assembly.5. Remove bolts (4) and remove carburetor (5) and gasket from the aftercooler housing.Install Carburetor
1. Put a new gasket and carburetor (1) in position and fasten to the aftercooler housing. 2. Slide hose (3) into position on the carburetor and tighten clamps (2).3. Connect the joint assembly to the carburetor with clamp (5), bolt and nut. Tighten nut to a torque of 49 4 lb.in. (5.5 N m).4. Fasten control rod (4) to the lever on the carburetor.5. Check the linkage adjustment. See GOVERNOR LINKAGE ADJUSTMENT in TESTING AND ADJUSTING.6. Turn on gas supply line to gas pressure regulator.Disassemble Carburetor
start by:a) remove carburetor 1. Remove bolts (1), washers, gasket and adapter (2) from the carburetor. 2. Remove screws (4), lockwashers and cover (3). 3. Remove spring (5) and diaphragm assembly (6). 4. Remove screws (7) and throttle plate (disc) (9).5. Remove throttle lever (8), lever stop and shaft as a unit. 6. Remove seal (10) from the nipple.7. Remove idle screw (11) and spring. Put identification marks on throttle (base) (13) and base assembly for use at assembly.8. Remove screws (12), lockwashers, throttle base (13) and gasket from the base assembly. 9. Use a screwdriver to remove retainer (14).10. Remove seal (15). 11. Remove bearing (16) from the throttle base (13).12. Turn the throttle base (13) over and do Steps 9 through 11.Assemble Carburetor
1. Install bearing (1) with tooling (A) to the bottom of the bearing bore in throttle base (2). 2. Put seal (4) in position in the seal and retainer counterbore.3. Install retainer (3) with tooling (A). 4. Turn throttle base (2) over and do Steps 1 through 3.5. Make an alignment of the identification marks and install the gasket and throttle base (2) on base assembly (5).
Be careful when the throttle shaft is installed not to cause damage to the seals.
6. Install idle screw (8), spring and seal (7).7. Turn power mixture adjustment (6) to center position between "R" (rich) and "L" (lean).
Be careful when the throttle shaft is installed not to cause damage to the seals.
8. Install throttle lever (9), lever stop and shaft. 9. Put throttle plate (disc) (10) in position on the throttle shaft. Install the screws and lockwashers that hold the throttle plate (disc) in position finger tight.10. Turn the throttle plate (disc) with throttle lever (9) from fully closed to fully open position to put the throttle plate (disc) in the center of the bore. Tighten the screws and make sure that the throttle lever turns freely. 11. Put diaphragm assembly (12) in position on base assembly (5). Install spring (11) on diaphragm assembly (12). 12. Put cover (13) in position on the diaphragm assembly. Install the five bolts and lockwashers that hold the cover in position. 13. Install adapter
1. Shut off gas supply line to gas pressure regulator. 2. Loosen clamps (1) and slide hose away from the carburetor.3. Disconnect control rod (2) from the carburetor lever. 4. Remove clamp (3) from the joint assembly.5. Remove bolts (4) and remove carburetor (5) and gasket from the aftercooler housing.Install Carburetor
1. Put a new gasket and carburetor (1) in position and fasten to the aftercooler housing. 2. Slide hose (3) into position on the carburetor and tighten clamps (2).3. Connect the joint assembly to the carburetor with clamp (5), bolt and nut. Tighten nut to a torque of 49 4 lb.in. (5.5 N m).4. Fasten control rod (4) to the lever on the carburetor.5. Check the linkage adjustment. See GOVERNOR LINKAGE ADJUSTMENT in TESTING AND ADJUSTING.6. Turn on gas supply line to gas pressure regulator.Disassemble Carburetor
start by:a) remove carburetor 1. Remove bolts (1), washers, gasket and adapter (2) from the carburetor. 2. Remove screws (4), lockwashers and cover (3). 3. Remove spring (5) and diaphragm assembly (6). 4. Remove screws (7) and throttle plate (disc) (9).5. Remove throttle lever (8), lever stop and shaft as a unit. 6. Remove seal (10) from the nipple.7. Remove idle screw (11) and spring. Put identification marks on throttle (base) (13) and base assembly for use at assembly.8. Remove screws (12), lockwashers, throttle base (13) and gasket from the base assembly. 9. Use a screwdriver to remove retainer (14).10. Remove seal (15). 11. Remove bearing (16) from the throttle base (13).12. Turn the throttle base (13) over and do Steps 9 through 11.Assemble Carburetor
1. Install bearing (1) with tooling (A) to the bottom of the bearing bore in throttle base (2). 2. Put seal (4) in position in the seal and retainer counterbore.3. Install retainer (3) with tooling (A). 4. Turn throttle base (2) over and do Steps 1 through 3.5. Make an alignment of the identification marks and install the gasket and throttle base (2) on base assembly (5).
Be careful when the throttle shaft is installed not to cause damage to the seals.
6. Install idle screw (8), spring and seal (7).7. Turn power mixture adjustment (6) to center position between "R" (rich) and "L" (lean).
Be careful when the throttle shaft is installed not to cause damage to the seals.
8. Install throttle lever (9), lever stop and shaft. 9. Put throttle plate (disc) (10) in position on the throttle shaft. Install the screws and lockwashers that hold the throttle plate (disc) in position finger tight.10. Turn the throttle plate (disc) with throttle lever (9) from fully closed to fully open position to put the throttle plate (disc) in the center of the bore. Tighten the screws and make sure that the throttle lever turns freely. 11. Put diaphragm assembly (12) in position on base assembly (5). Install spring (11) on diaphragm assembly (12). 12. Put cover (13) in position on the diaphragm assembly. Install the five bolts and lockwashers that hold the cover in position. 13. Install adapter
Cat SIS web machinery list:
Parts shaft Caterpillar catalog:
6E3651
SHAFT
966D, 966F, 966F II, R1300, R1300G, R1300G II
966D, 966F, 966F II, R1300, R1300G, R1300G II
1T1484
SHAFT AS-CENTER
950B, 950B/950E, 950F
950B, 950B/950E, 950F
7G7047
SHAFT
950B, 950B/950E, 950F
950B, 950B/950E, 950F
4T2111
SHAFT
814F, 814F II, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F
814F, 814F II, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F
1T1942
SHAFT AS-CENTER
950F, 950F II, 960F
950F, 950F II, 960F
4J8145
SHAFT
950, 966C, 966R
950, 966C, 966R
5J2604
SHAFT
814, 815, 950, 966C, 966R
814, 815, 950, 966C, 966R
8K5453
SHAFT ASSEM.
815, 966C, 966R
815, 966C, 966R
7K7995
SHAFT ASSEM.
815, 966C
815, 966C
2V6221
SHAFT
528, 815, 966C
528, 815, 966C
8K6285
SHAFT
814, 815, 816, 966C
814, 815, 816, 966C
5V0574
SHAFT
950B, 950B/950E
950B, 950B/950E
1149036
SHAFT-INPUT
936F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
936F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
6Y7880
SHAFT-PLANETARY
950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300G II
950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300G II
9C8421
SHAFT-AXLE
950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1575547
SHAFT-OUTPUT
950G, 950G II, 950H, 962G, 962G II, IT62G, IT62G II
950G, 950G II, 950H, 962G, 962G II, IT62G, IT62G II
9C5853
SHAFT-PINION
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1120742
SHAFT-BEVEL PINION
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1803995
SHAFT
824G, 825G, 826G, 950G, 950G II, 962G, 962G II, 966G, 966G II, 966H, 972G, 972G II, 980G, 980G II, 980H, IT62G, R1600G
824G, 825G, 826G, 950G, 950G II, 962G, 962G II, 966G, 966G II, 966H, 972G, 972G II, 980G, 980G II, 980H, IT62G, R1600G
1803994
SHAFT AS
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H, 986H, 98...
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H, 986H, 98...
1684850
SHAFT AS
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
1137751
SHAFT
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
1152023
SHAFT-OUTPUT
950F II, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H, R1300G II
950F II, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H, R1300G II
3T9958
SHAFT
936, 936F, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, G936, IT62G, IT62G II, IT62H
936, 936F, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, G936, IT62G, IT62G II, IT62H