8E1157 SHAFT-TRANSMISSION INPUT Caterpillar parts
589, D10N, D8L, D9N, D9R
Rating:
Alternative (cross code) number:
CA8E1157
8E-1157
8E1157
CA8E1157
8E-1157
8E1157
Weight: 36 pounds 16 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$626.30
29 Apr 2022
US: Florida-Parts-Z
8E1157 - Shaft 9P5537, 7T2170 fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$626.20
26 Mar 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar Shaft 8E1157 New
$380.39
29 Apr 2018
3768 Hundredths Pounds
CTP: CTP
Caterpillar SHAFT (8E1157)
8E1157 Caterpillar Weight(lbs): 37.60 Length(cm): 96.0000 Width(cm): 12.0000 Depth(cm): 12.0000
8E1157 Caterpillar Weight(lbs): 37.60 Length(cm): 96.0000 Width(cm): 12.0000 Depth(cm): 12.0000
This part in 2 request:
Show.
This information for suppliers only!
2023-02-09
2023-02-09
Number on catalog scheme:
25
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 9S-1366 Bolt 2 Start By:
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Illustration 1 g01205960
Remove bolts (5) and gear (4) .
Put an alignment mark across housing (1) and water pump housing (3). The orientation of the housings is different on the left water pump and the right water pump.
Remove bolts (2). Separate housing (1) from water pump housing (3). Remove the O-ring seal from water pump housing (3) .
Illustration 2 g01205982
Loosen bolt (6). Do not remove the bolt. Use a block and Tooling (B) in order to put tension on the impeller. Tap the center of the block in order to loosen impeller (8) on the shaft. Remove bolt (6) and washer (7) .
Illustration 3 g01205985
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove impeller (8) .
Illustration 4 g01206070
Illustration 5 g01206072
Remove spring (10) from shaft (9) .
Remove seal (11) .
Illustration 6 g01206073
Remove bolts (12) and thrust washer (13) .
Illustration 7 g01206085
Remove shaft (9) .
Illustration 8 g01206088
If necessary, use Tooling (A) and a suitable press in order to remove seal (14) .Note: Check the O-ring seals for wear or damage. If necessary, replace the O-ring seals.
Illustration 9 g01206116
Remove bearings (15) and bearings (16) from water pump housing (3) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 9S-1366 Bolt 2 Start By:
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Illustration 1 g01205960
Remove bolts (5) and gear (4) .
Put an alignment mark across housing (1) and water pump housing (3). The orientation of the housings is different on the left water pump and the right water pump.
Remove bolts (2). Separate housing (1) from water pump housing (3). Remove the O-ring seal from water pump housing (3) .
Illustration 2 g01205982
Loosen bolt (6). Do not remove the bolt. Use a block and Tooling (B) in order to put tension on the impeller. Tap the center of the block in order to loosen impeller (8) on the shaft. Remove bolt (6) and washer (7) .
Illustration 3 g01205985
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Remove impeller (8) .
Illustration 4 g01206070
Illustration 5 g01206072
Remove spring (10) from shaft (9) .
Remove seal (11) .
Illustration 6 g01206073
Remove bolts (12) and thrust washer (13) .
Illustration 7 g01206085
Remove shaft (9) .
Illustration 8 g01206088
If necessary, use Tooling (A) and a suitable press in order to remove seal (14) .Note: Check the O-ring seals for wear or damage. If necessary, replace the O-ring seals.
Illustration 9 g01206116
Remove bearings (15) and bearings (16) from water pump housing (3) .
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
AD40, AD45, AE40, D10, D10N, D10R, D11N, D11R, D8L, D9L, D9N, D9R, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R2900G, R3000H
D9R, D9T
D9R, D9T
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2
D10, D10N, D11N, D8L, D9L, D9N, D9R
D10N, D10R, D10T, D10T2
D10N, D10R
D10N, D10R, D9L
D10N, D9L
589, 824C, 826C, 834B, 980C, 980F, 980G, 983B, 988B, D10N, D400, D44B, D550B, D8L, D9L, D9N
589, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836...
9W2981
SHAFT AS-OUTPUT
589, D10N, D9N, D9R
589, D10N, D9N, D9R
589, D10N, D8L, D9L, D9N
589, 834B, AD30, D10N, D10R, D10T, D10T2, D350E, D350E II, D400, D400E, D44B, D550B, D8L, D9L, D9N, D9R, D9T, R2900, R2900G, R3000H
6Y5946
SHAFT-BEVEL GEAR
589, D10N, D8L, D9N, D9R
589, D10N, D8L, D9N, D9R
8P0311
SHAFT
578, 583R, 587R, 589, D10N, D6H, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9L, D9R
578, 583R, 587R, 589, D10N, D6H, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9L, D9R
589, D10N, D8L, D9L, D9N
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
589, D8L, D9L
589, D10N, D9R
589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980...