9N3342 SHAFT Caterpillar parts
215, 3204, 3208, 517, 527, 613C, 916, 926, 953, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, FB221, IT18B, IT28, PS-500
Rating:
Alternative (cross code) number:
CA9N3342
9N-3342
9N3342
CA9N3342
9N-3342
9N3342
Weight: 0.60 pounds 0 kg.
EXCAVATOR, WHEEL TRACTOR,
This part in 2 request:
Show.
This information for suppliers only!
2023-01-19
2021-05-14
Compatible equipment models: 9N3342:
Number on catalog scheme:
13
For full view, you need register
Information:
Remove Fuel Injection Lines
start by: a) remove aftercooler core 1. Remove the bolts (1) and locks that hold the aftercooler housing in position.2. Disconnect bleed line (3) from fuel filter.3. Disconnect the sensing line (4) from the fuel ratio control.4. Remove the aftercooler housing (2).5. Disconnect the fuel injection lines from the camshaft housing.6. Disconnect the injection lines (5) from fuel injection pumps. Remove fuel injection lines. Install caps or plugs in all lines or openings.Install Fuel Injection Lines
1. Remove the plugs and caps from fuel injection lines and openings. 2. Put the fuel injection lines in position, and tighten the nuts (4) to 30 5 lb.ft. (4.1 0.7 mkg).3. Put the aftercooler housing (2) in position, and install the bolts and locks.4. Connect the sensing line (1) to the fuel ratio control.5. Connect the bleed line (3) to filter housing.end by: a) install aftercooler core
start by: a) remove aftercooler core 1. Remove the bolts (1) and locks that hold the aftercooler housing in position.2. Disconnect bleed line (3) from fuel filter.3. Disconnect the sensing line (4) from the fuel ratio control.4. Remove the aftercooler housing (2).5. Disconnect the fuel injection lines from the camshaft housing.6. Disconnect the injection lines (5) from fuel injection pumps. Remove fuel injection lines. Install caps or plugs in all lines or openings.Install Fuel Injection Lines
1. Remove the plugs and caps from fuel injection lines and openings. 2. Put the fuel injection lines in position, and tighten the nuts (4) to 30 5 lb.ft. (4.1 0.7 mkg).3. Put the aftercooler housing (2) in position, and install the bolts and locks.4. Connect the sensing line (1) to the fuel ratio control.5. Connect the bleed line (3) to filter housing.end by: a) install aftercooler core
Cat SIS web machinery list:
Parts shaft Caterpillar catalog:
613, 613B, 613C, 613C II, 613G
613, 613B, 613C, 613C II, 613G
613B, 613C, 613C II, 613G
916, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 926, IT18B, IT18F, IT24F, IT28
916, 920, IT18B
910, 916, IT18B
814B, 815B, 824C, 826C, 916, 926, 936, 936F, 950B, 950F, 950F II, 966D, 966F, 980C, 980F, G936, IT18B, IT28B
508, 518, 926, 936, D250B, D250E, D250E II, D300B, D300D, G926, G936, IT28, IT28B
910, 916, 926, IT28
926, IT28, IT28B
926, IT28
916, 926, IT18, IT18B, IT28, IT28B
4P4793
SHAFT
231D, 3208
231D, 3208
9Y1680
SHAFT AS
3508, 3512, 3516
3508, 3512, 3516
2W0146
SHAFT-SETTING
3512, 3516, 3606, 3608, 3612, 3616, G3508, G3512, G3516
3512, 3516, 3606, 3608, 3612, 3616, G3508, G3512, G3516
4P6899
SHAFT-SPEED SET
3508, 3512, 3516, 3606, 3608, 3612, 3616
3508, 3512, 3516, 3606, 3608, 3612, 3616
1029453
SHAFT
3512, 3512B, 3516, 3516B, G3512, G3516
3512, 3512B, 3516, 3516B, G3512, G3516
5S6694
SHAFT ASSEM.
1673
1673
1239391
SHAFT-STUB
3508B
3508B
6L3023
SHAFT-IDLER
3412, 3412C, 3412E, 3508, 3512, 3516, D398, D398B, D399, G3412, G3516, G399
3412, 3412C, 3412E, 3508, 3512, 3516, D398, D398B, D399, G3412, G3516, G399
6L3025
SHAFT-FAN
3412, 3412C, 3412E, 3508, 3512, D398, D398B, G3412, G3516, G399
3412, 3412C, 3412E, 3508, 3512, D398, D398B, G3412, G3516, G399
1976850
SHAFT
3412, 3508, 3508B, 3512, 3512B, 3516, 3516B
3412, 3508, 3508B, 3512, 3512B, 3516, 3516B
2005268
SHAFT
3406C, 3412, 3508, 3508B, 3512, 3512B, 3516, 3516B, G3516, PM3412, PM3508, PM3512, PM3516
3406C, 3412, 3508, 3508B, 3512, 3512B, 3516, 3516B, G3516, PM3412, PM3508, PM3512, PM3516
7E0296
SHAFT AS-TURBINE
3406B
3406B