SHAFT A. 9S6068 - Caterpillar

Illustration 3 g06223542
View of the right-hand side of the left-hand lift arm.
(6) 9R-2821 Boss
(18) 163-9662 Threaded Boss
(28) 9C-4935 Plate
Weld bosses and plates as shown.
Illustration 4 g06223781
Inside the left-hand loader arm.
(3) 6V-9829 CAP
(4) 8T-4121 WASHER-HARD
(5) 8T-4137 BOLT-HEX HEAD M10x1.5
(8) 096-6166 WASHER-HARD
(9) 112-1817 VALVE-BALL
(10) 121-4405 BOLT-HEX HEAD
(12) 148-8336 ADAPTER AS
(18) 163-9662 BOSS
(19) 324-3471 BRACKET
(25) 533-4378 HOSE AS
(26) 536-6864 WIRING GP-CPLR
(27) 6D-4246 CLIP-LOOP
(28) 9C-4935 PLATE M10X1.5
Install hoses, clips, bracket and ball valves.Note: Part number (26) attaches to the tilt level sensor.
Illustration 5 g06223862
(4) 8T-4121 WASHER-HARD
(5) 8T-4137 BOLT-HEX HEAD M10x1.5
(20) 390-7970 VALVE GP-MTG &
(22) 533-0870 BRACKET
(25) 533-4378 HOSE AS
(26) 536-6864 WIRING GP-CPLR
(27) 6D-4246 CLIP-LOOP
Route hoses and connect as shown.
Illustration 6 g06223901
Close up of area A.
(1) 7X-2534 BOLT-HEX HEAD M6x1
(2) 5C-2890 NUT-HEX
(7) 9X-8256 WASHER
(11) 148-8321 CONNECTOR AS
(12) 148-8336 ADAPTER AS
(14) 148-8378 ADAPTER AS
(20) 390-7970 VALVE GP-MTG &
(25) 533-4378 HOSE AS
(26) 536-6864 WIRING GP-CPLR
Install valve group (20) to the block on the frame as shown.
Illustration 7 g06223911
(4) 8T-4121 WASHER-HARD
(5) 8T-4137 BOLT-HEX HEAD M10x1.5
(15) 148-8433 ADAPTER AS
(16) 154-5020 HOSE AS
(17) 163-7039 HOSE AS
(24) 533-3324 BRACKET AS
(27) 6D-4246 CLIP-LOOP
Connect and route hoses as shown.Note: For adapter (15), remove elbow from implement lines group and replace it adapter tee (15).
Illustration 8 g06223926
(4) 8T-4121 WASHER-HARD
(5) 8T-4137 BOLT-HEX HEAD M10x1.5
(13) 148-8367 ADAPTER AS
(17) 163-7039 HOSE AS
(23) 533-3187 BRACKET AS
(27) 6D-4246 CLIP-LOOP
Route hose (17) to the brake lines group cylinders, remove cap from the tee and install elbow (13), then connect hose (17).
Illustration 9 g06223938
Right-hand switch panel in the cab.
(21) 474-6211 SWITCH GP
Install the coupler switch in the right-hand panel in the cab.
Unless specified, tighten all hardware and fittings to standard torque.
Check for leaks.