9W9069 SHAFT-INPUT Caterpillar parts
814B, 815B, 966D, 966F, 966F II, 970F
Rating:
Alternative (cross code) number:
CA9W9069
9W-9069
9W9069
CA9W9069
9W-9069
9W9069
Weight: 25 pounds 11 kg.
SOIL COMPACTOR, WHEEL LOADER,
Related part:
9W9069
SHAFT-INPUT-YM
5241299
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$537.25
24 Feb 2019
Unknown: Unknown
Caterpillar 9W9069 Shaft New
$307.48
09 Jun 2022
US: ProperBuy
9W9069 Shaft Fits Caterpillar 815B 966F 966F II 970F
TCP Warranty
TCP Warranty
Number on catalog scheme:
81
For full view, you need register
Compatible equipment models: 9W9069:
Information:
Removal Procedure
Start By:
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Remove the housing for the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00541252
Remove two socket head bolts (1) that hold bridge (2) in position.
Remove bridge (2) from the cylinder block.
Illustration 2 g00541253
Note: Inspect the main bearing caps and the connecting rod caps for the proper identification marks. The identification marks should give the location and the direction of the bearings in the engine.
Remove ten main bearing cap bolts (3) from the main bearing caps.
Remove five main bearing caps (4) from the cylinder block.
Remove the lower main bearings and the lower thrust washers. Keep the lower main bearings with the respective main bearing caps.
Illustration 3 g00541254
Note: The connecting rod caps can be held on the connecting rod with two bolts and two nuts. The connecting rod caps can also be held on the connecting rod with two bolts that are threaded into the connecting rod.
Remove eight nuts (5) from the connecting rod caps.
Remove four connecting rod caps (6) from the connecting rods.
Remove the bearings from connecting rod caps (6). Keep the connecting rod bearings with the respective connecting rod cap.
Do not allow the connecting rods to strike the piston cooling jets. Damage or misalignment may occur.
Push the piston assemblies into the cylinder bores.
Illustration 4 g00541256
Attach lifting straps and a suitable lifting device to crankshaft (7) .
Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is 29 kg (65 lb). Do not scratch any of the finished surfaces on the crankshaft.
Illustration 5 g00541257
Remove upper main bearings (8) and upper thrust washers (9) from the cylinder block.
Start By:
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Remove the housing for the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00541252
Remove two socket head bolts (1) that hold bridge (2) in position.
Remove bridge (2) from the cylinder block.
Illustration 2 g00541253
Note: Inspect the main bearing caps and the connecting rod caps for the proper identification marks. The identification marks should give the location and the direction of the bearings in the engine.
Remove ten main bearing cap bolts (3) from the main bearing caps.
Remove five main bearing caps (4) from the cylinder block.
Remove the lower main bearings and the lower thrust washers. Keep the lower main bearings with the respective main bearing caps.
Illustration 3 g00541254
Note: The connecting rod caps can be held on the connecting rod with two bolts and two nuts. The connecting rod caps can also be held on the connecting rod with two bolts that are threaded into the connecting rod.
Remove eight nuts (5) from the connecting rod caps.
Remove four connecting rod caps (6) from the connecting rods.
Remove the bearings from connecting rod caps (6). Keep the connecting rod bearings with the respective connecting rod cap.
Do not allow the connecting rods to strike the piston cooling jets. Damage or misalignment may occur.
Push the piston assemblies into the cylinder bores.
Illustration 4 g00541256
Attach lifting straps and a suitable lifting device to crankshaft (7) .
Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is 29 kg (65 lb). Do not scratch any of the finished surfaces on the crankshaft.
Illustration 5 g00541257
Remove upper main bearings (8) and upper thrust washers (9) from the cylinder block.
Caterpillar parts catalog:
Parts shaft Caterpillar catalog:
814F, 814F II, 966F, 966F II, 970F
814B, 815B, 966D, 966F
814B, 815B, 966D, 966F
966D, 966F, 966F II, R1300, R1300G, R1300G II
814F, 814F II, 815F, 815F II, 816F, 816F II, 970F
528B, 530B, 814B, 815B, 816B, 966D, 966F, D25C, D25D, D30C, D350C, D350E, D35C, D35HP, D400
814B, 815B, 816B, 966D, 966F
966D
815B, 816B, 966D
815B, 816B, 966D
814B, 815B, 816B, 966D, 966F, 966G
735, 815B, D350E II
814F, 814F II, 966F, 966F II, 970F
814F, 814F II, 966F, 966F II, 970F
966F, 966F II, 970F, D25D, D300E, D350E, D400E
6E2509
SHAFT
994, 994D, 994F, 994H
994, 994D, 994F, 994H
1342236
SHAFT-DRIVE
994, 994D
994, 994D
6E1035
SHAFT
994, 994D
994, 994D
950B, 950B/950E, 950F
8R9307
SHAFT-PINION
950F, 950F II, 960F, D250B, D250D, D250E, D300B, D300D
950F, 950F II, 960F, D250B, D250D, D250E, D300B, D300D
8R8381
SHAFT AS
950F, 966F, 966F II, 980F, 980F II
950F, 966F, 966F II, 980F, 980F II
966D, 966F, 966F II, R1300, R1300G, R1300G II
814B, 815B, 966D, 966F
814B, 815B, 966D, 966F