SHEET-RH 1437946 - Caterpillar

1437946 SHEET-RH Caterpillar parts 527

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1437946
143-7946
1437946

Weight: 4 pounds 2 kg.

Buy SHEET-RH 1437946 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK SKIDDER,

Compatible equipment models: 1437946:

TRACK SKIDDER 527 Caterpillar

Number on catalog scheme: 10

Caterpillar 1437946 Parts scheme SHEET-RH

For full view, you need register

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

527 Track Skidder J6800001-UP (MACHINE) POWERED BY C7.1 Engine

472-3831: PANEL GP-SIDE » (RH) M00797900130

527 TRACK-TYPE SKIDDER 2RS00001-UP (MACHINE) POWERED BY 3304 Engine

131-8492: PANEL GP-SIDE » (RH) SEBP25600200
131-8779: PANEL GP-SIDE » (RH) SEBP25600201

527 TRACK-TYPE SKIDDER 3DS00001-UP (MACHINE) POWERED BY 3304 Engine

131-8779: PANEL GP-SIDE » (RH) SEBP25900204

527 TRACK-TYPE SKIDDER Grapple 4NS00001-UP (MACHINE) POWERED BY 3304 Engine

131-8492: PANEL GP-SIDE » (RH) SEBP26620206
131-8779: PANEL GP-SIDE » (RH) SEBP26620207

527 Track Skidder JSR00001-UP (MACHINE) POWERED BY 3304 Engine

131-8492: PANEL GP-SIDE » (RH) SEBP51010172
131-8779: PANEL GP-SIDE » (RH) SEBP51010173

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03413500
Illustration 2 g03364097
Ensure that crankshaft flange (1) is clean, dry, and free from damage. Clean the crankshaft flange with lint free cloth.
Ensure that the face of the cylinder block and the bridge piece are clean and dry.
A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve.
Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block. Tightening sequence for the crankshaft rear seal
Illustration 3 g03364098
Install torx screws (4) finger tight. Note: Do not install torx screws to Positions (X) at this stage.
Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N m (195 lb in). Tighten torx screws (4) in the sequence that is shown in Illustration 3.
Remove Tooling (B).
Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N m (195 lb in). Refer to Illustration 3. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".