AVSPARE.COM
parts catalog

SHEET AS 3727624 - Caterpillar



3727624 SHEET AS Caterpillar parts 315D L, 319D L SHEET
Rating:
79
Alternative (cross code) number:
CA3727624
372-7624
3727624
Caterpillar 3727624 SHEET AS

Buy SHEET AS 3727624 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3727624:

EXCAVATOR  315D L   319D L   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Put a small amount of clean engine oil or glycerine on the lip of seal (4) and in the bores for the O-ring seals at assembly.(1) Distance bearing is installed below pipe surface ... 0.25 0.25 mm (.010 .010 in.)(2) Diameter of shaft ... 15.80 0.03 mm (.622 .001 in.) Bore in bearings ... 15.88 mm (.625 in.)Bore in pipe for bearings ... 18.263 0.013 mm (.7190 .0005 in.)(3) Valve assembly shown in the "run" (open) position. When the valve is closed a 0.08 mm (.003 in.) feeler gauge must not fit between the valve and the bore in the pipe at any point.(4) Seal. Install the seal with the tip of the seal toward the outside as shown.(5) Diameter of shaft ... 9.60 0.03 mm (.378 .001 in.) Bore in the bearing ... 9.80 0.03 mm (.386 .001 in.) Adjust shaft as needed to change spring tension until hold-in current consumption (draw) is less than 2A at shutdown.(6) 3N9106 Torsion Spring (used with some 3406 Engines): Free length ... 63.5 mm (2.50 in.)Outside diameter ... 30.7 mm (1.21 in.)5N2761 Torsion Spring:Free length ... 49.8 0.5 mm (1.96 .02 in.)Outside diameter ... 30.7 0.5 mm (1.21 .02 in.)(7) 3N7848 Spring: Length under test force ... 22.86 0.5 mm (.90 .02 in.)Test force ... 4 N (1 lb.)Free length after test ... 35.6 0.5 mm (1.40 .02 in.)Outside diameter ... 18.8 0.5 mm (.74 .02 in.)(8) Bracket assembly. Bracket assembly must be adjusted so valve assembly (3) is parallel to pipe bore within 2°.(9) 4N3889 Solenoid: Voltage rating ... 12VCurrent consumption (draw): Pull-in windings ... 21A at 12VHold-in windings ... Below 1A at 14.3V4N3890 Solenoid:Voltage rating ... 24 or 32VCurrent consumption (draw): Pull-in windings ... 10A at 24VHold-in windings ... Below 1A at 28V4N3889 and 4N3890 Solenoids:Plunger travel ... 11.7 0.3 mm (.46 .01 in.)Distance from plunger face to flange face: with solenoid energized* ... 9.6 0.5 mm (.38 .02 in.)with plunger extended ... 21.28 0.13 mm (.838 .005 in.)*The hold-in current consumption (draw) on engine must take less than 2A at shutdown.(10) Diode assembly. Diode assembly required to suppress the back EMF voltage spike generated when the solenoid is turned off.

Caterpillar parts catalog:

Caterpillar parts catalog
315D L Excavator KBD00001-UP (MACHINE) POWERED BY C4.2 Engine
319D L & 319D LN Excavators AYF00001-UP (MACHINE) POWERED BY C4.2 Engine


Parts sheet Caterpillar catalog:

2680655 SHEET AS-SOUND SUPPRESSION
315D L, 318D L, 319D L, 319D LN
2369440 SHEET
312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 315D L, 318D L, 318D2 L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 323D L, 323D LN, 323D SA, 324D, ...
2680697 SHEET AS
315D L, 318D L, 319D, 319D L, 319D LN
3039858 SHEET AS
315D L, 318D L, 319D, 319D L, 319D LN
2680653 SHEET AS
315D L, 318D L, 319D, 319D L, 319D LN
2680659 SHEET AS
315D L, 318D L, 319D, 319D L, 319D LN
2680493 SHEET-RUBBER
315D L, 318D L, 319D, 319D L, 319D LN
2680673 SHEET AS
315D L, 318D L, 319D, 319D L, 319D LN
2931218 SHEET AS
314D CR, 314D LCR
3346493 SHEET AS
312D, 312D L, 312E, 312E L, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 32...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.