SHIM 1170754 - Caterpillar

Illustration 1 g03245477
Front view of engine
Table 1
Specification for 383-7229 Cylinder Block Gp
Item Qty Part Specification Description
During assembly, bottom of the spacer plate, top of the block, and both the sides of the gasket plate must be free of all visible fuel, oil, water and gasket adhesives, assembly compounds, or any other contaminates.
1 4 5F-9657 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
2 10 101-1198 Camshaft Bearing The camshaft bearing joint must be on the horizontal centerline of the bore.
Oil holes must be positioned from horizontal at an angle (C) of 20.0 0.5 degrees as shown in Illustration 1.
After installation, bore is 92.00 0.08 mm (3.622 0.003 inch).
3 8 6V-3348 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
A 16 8T-0099 Dowel Extension of the dowel from the top face of the cylinder block is 20.0 0.5 mm (0.79 0.02 inch).
B 8 197-7008 Dowel Extension of the dowel from the top face of the cylinder block is 21.0 0.5 mm (0.83 0.02 inch).
D - - New dimension from centerline of crankshaft bearing bore to bottom of cylinder block (pan rails) is 230 mm (9.1 inch).
E - - Bore in the cylinder block for the main bearings is 169.742 0.020 mm (6.6827 0.0008 inch).
Illustration 2 g03245478
Right side view
Table 2
Item Qty Part Specification Description
The camshaft bearings (2) are installed into the cylinder block at the following positions:
- - - Distance (F) is 1120.0 1.5 mm (44.09 0.06 inch).
- - - Distance (G) is 850.0 1.5 mm (33.46 0.06 inch).
- - - Distance (H) is 580.0 1.5 mm (22.83 0.06 inch).
- - - Distance (J) is 310.0 1.5 mm (12.20 0.06 inch).
- - - Distance (K) is 40.0 0.5 mm (1.57 0.02 inch).
4 3 7N-2047 Dowel Extension (L) of the dowel is 6.0 0.5 mm (0.24 0.02 inch).
5 2 8T-2929 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
6 2 8T-2928 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
7 2 4N-0683 Dowel Extension (M) of the dowel is 19.0 0.5 mm (0.75 0.012 inch).
8 2 7N-2044 Dowel Extension (N) of the dowel is 40.0 0.5 mm (1.57 0.02 inch).
Illustration 3 g03245479
Front view
Table 3
Item Qty Part Specification Description
R - - New dimension from centerline of crankshaft bearing bore to the top of the cylinder block is 586 mm (23.1 inch).
9 8 352-6061 Liner Seal Assemble liner seals dry on clean and dry liner grooves.
Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap.
10 24 7N-2046 O-Ring Seal Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap.
11 5 223-1696 Crankshaft Bearing Cap Width of the crankshaft bearing cap is 340.030 0.015 mm (13.3870