1235364 SHIM Caterpillar parts
350, 350 L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
Rating:
Alternative (cross code) number:
CA1235364
123-5364
1235364
CA1235364
123-5364
1235364
Weight: 1 pounds 0 kg.
Information:
ID
152
mm
MATERIAL THICKNESS
2
mm
OD
260
mm
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 1235364:
Number on catalog scheme:
4
For full view, you need register
Information:
Replacement of Serviced Parts for 8T-2701 Blowby Indicator Assembly
Removal Procedure for the 8T-0999 Membrane Switch
Remove the rear cover and remove the internal battery. Follow Steps 1 and 2 in "Replacing the Internal Battery".
Remove the small printed circuit board. Follow Step 3 and 4 in "Disabling the Auto Turn-off Feature (If Equipped)".
Illustration 21 g03033608
Remove six screws (3). Lift up the printed circuit board (4) from the front cover. Be sure to lift the printed circuit board from the LCD end.
Illustration 22 g03033613
Carefully remove the 8T-0999 Membrane Switch connector (5) from the connector pins (6) .Replacement Procedure for the 8T-0844 Front Cover and the 8T-0999 Membrane Switch
Note: Always replace both the front cover and the membrane switch even if only one is damaged.
Repeat steps 1 through 4 of "Removal Procedure for the 8T-0999 Membrane Switch"
Start at the window end of the membrane switch. Carefully peel the backing from the 8T-0999 Membrane Switch while you align the membrane switch with the 8T-0844 Front Cover .Note: Before you glue the switch in place, make sure that the switch connector is properly installed through the slot in the front cover.Replacing the 8T-0887 Connector Assembly or the 8T-1005 LCD Display
Illustration 23 g03033777
Repeat steps 1 through 4 of "Removal Procedure for the 8T-0999 Membrane Switch".
Remove four screws (7) from circuit board (4) .
Illustration 24 g03033857
Illustration 25 g03035356
Remove 8T-0887 Connector Assembly (8) and 8T-1005 LCD Display (12) from the circuit board.Note: The 8T-0887 Connector Assembly consists of the following items: Cover (10), Shield (11), LCD Display (12), Frame (13), and Strips (14) .Note: Do not touch strips (14) with bare hands. If the strips need to be placed into the slots in the frame (13), use tweezers.
Illustration 26 g03035436
Discard damaged parts.Note: The pins on the bottom of the frame of the connector must fit into the holes (15) .
Illustration 27 g03035447
Place the assembled frame (13) and strips (14) on the large circuit board.
Hold the digital LCD display (12) in front of a light in order to determine which end the LO BAT display is on. Do not lose this orientation.
Place the LCD display on top of the strips with the LO BAT on the left.
Place shield (11) on top of the LCD display. Put cover (10) over the shield and install four screws (7) in the large circuit board.
Make sure that the connector for the membrane switch (5) is properly aligned with the pins (6 on the large circuit board. Press the components together.)
Install six screws (3). Carefully place the small circuit board on top of the large circuit board.
Align the connector for the circuit boards before you press the two boards together.
Install four screws (1) in the corners of the small circuit board (2). Replace the battery and the rear cover.Repair Information
If the blowby/airflow indicator does not operate correctly, install a new internal battery. Recheck the operation. If the blowby/airflow indicator is faulty, contact Dealer Service Tools for repair locations.Units that are less than one year old will be repaired under the warranty. The cost
Removal Procedure for the 8T-0999 Membrane Switch
Remove the rear cover and remove the internal battery. Follow Steps 1 and 2 in "Replacing the Internal Battery".
Remove the small printed circuit board. Follow Step 3 and 4 in "Disabling the Auto Turn-off Feature (If Equipped)".
Illustration 21 g03033608
Remove six screws (3). Lift up the printed circuit board (4) from the front cover. Be sure to lift the printed circuit board from the LCD end.
Illustration 22 g03033613
Carefully remove the 8T-0999 Membrane Switch connector (5) from the connector pins (6) .Replacement Procedure for the 8T-0844 Front Cover and the 8T-0999 Membrane Switch
Note: Always replace both the front cover and the membrane switch even if only one is damaged.
Repeat steps 1 through 4 of "Removal Procedure for the 8T-0999 Membrane Switch"
Start at the window end of the membrane switch. Carefully peel the backing from the 8T-0999 Membrane Switch while you align the membrane switch with the 8T-0844 Front Cover .Note: Before you glue the switch in place, make sure that the switch connector is properly installed through the slot in the front cover.Replacing the 8T-0887 Connector Assembly or the 8T-1005 LCD Display
Illustration 23 g03033777
Repeat steps 1 through 4 of "Removal Procedure for the 8T-0999 Membrane Switch".
Remove four screws (7) from circuit board (4) .
Illustration 24 g03033857
Illustration 25 g03035356
Remove 8T-0887 Connector Assembly (8) and 8T-1005 LCD Display (12) from the circuit board.Note: The 8T-0887 Connector Assembly consists of the following items: Cover (10), Shield (11), LCD Display (12), Frame (13), and Strips (14) .Note: Do not touch strips (14) with bare hands. If the strips need to be placed into the slots in the frame (13), use tweezers.
Illustration 26 g03035436
Discard damaged parts.Note: The pins on the bottom of the frame of the connector must fit into the holes (15) .
Illustration 27 g03035447
Place the assembled frame (13) and strips (14) on the large circuit board.
Hold the digital LCD display (12) in front of a light in order to determine which end the LO BAT display is on. Do not lose this orientation.
Place the LCD display on top of the strips with the LO BAT on the left.
Place shield (11) on top of the LCD display. Put cover (10) over the shield and install four screws (7) in the large circuit board.
Make sure that the connector for the membrane switch (5) is properly aligned with the pins (6 on the large circuit board. Press the components together.)
Install six screws (3). Carefully place the small circuit board on top of the large circuit board.
Align the connector for the circuit boards before you press the two boards together.
Install four screws (1) in the corners of the small circuit board (2). Replace the battery and the rear cover.Repair Information
If the blowby/airflow indicator does not operate correctly, install a new internal battery. Recheck the operation. If the blowby/airflow indicator is faulty, contact Dealer Service Tools for repair locations.Units that are less than one year old will be repaired under the warranty. The cost
Cat SIS web machinery list:
Parts shim Caterpillar catalog:
307B, 307C, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 325D L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, ...
315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
308C, 308E SR, 320C, 322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D ...
325C, 325C FM, 325C L, 325D, 325D FM, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C...
330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 345C L, 350, 350 L, 365B, 375, 5080, 950K, 962K, M318C, M318C MH, M318D, M318D MH, M322C, M322D, M322D MH, TK1051, W330B
325C, 325C FM, 325C L, 325D L, 325D MH, 330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 350, 350 ...
308C, 320C, 322B LN, 322C, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E...
312D2, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, E450, W3...
312D2, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390F L, 5080, E450, W3...
115, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D, 3...
115, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D, 3...
324D L, 325D L, 328D LCR, 329D L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LN, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, ...
350, 350 L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
1748354
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
2276180
SHIM
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
2276179
SHIM
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
2276177
SHIM
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
2084154
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
2084152
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
2084151
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
2084150
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
2084153
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
2084149
SHIM
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B
385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B