AVSPARE.COM
parts catalog

SHIM PACK 1308707 - Caterpillar


1308707 SHIM PACK Caterpillar parts 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, IT38G II
Rating:
26
Alternative (cross code) number:
CA1308707
130-8707
1308707
Caterpillar 1308707 SHIM PACK
Weight: 0.100 pounds 0 kg.

Buy SHIM PACK 1308707 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 1308707:

INTEGRATED TOOLCARRIER  IT38G II  
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Illustration 1 g03382615
Motor Grader Applications
Note: The following schematic is used for Articulated Truck Applications
Illustration 2 g03382609
Articulated Truck Applications
Table 2
Troubleshooting Test Steps Values Results
1. Check for Fault Codes
A. Turn the key switch to the ON position.
B. Connect Cat ET.
C. Record the Fault Codes.
Codes
Result: An E1190 (3) or a 3548-8 is present.
Proceed to Test Step 2.
Result: A 3548-5 or a 3548-6 present.
Proceed to Test Step 6.
Result: A 3548-11 is present.
Proceed to Test Step 9.
Result: An E1352 (3) is present.
Proceed to Test Step 11.
2. Inspect the Fan
A. Inspect the fan for the following conditions:
- Damaged fan blades
- Debris against the fan blades
- Air flow is obstructed
Fan
Result: The Fan is OK.
Proceed to Test Step 3.
Result: The fan is obstructed.
Repair: Remove the obstruction. Verify that the problem is resolved.
Result: The fan is damaged.
Repair: Replace the fan. Verify that the problem is resolved.
3. Check for Voltage at the Fan
A. Disconnect the two-pin connector to the fan.
B. Measure the voltage between pins 1 and 2 on the connector.
Battery Voltage
Result: The voltage is OK.
Proceed to Test Step 4.
Result: The voltage is not OK.
Repair: The problem is in the wiring between the fan and the battery. Check the fuse between the fan and the battery. Repair or replace the wiring harness.
Return to service.
4. Check for Continuity Between the Fan and the ECM
A. Turn the keyswitch to the OFF position.
B. Disconnect the four-pin connector from the aftertreatment cooling fan.
C. Disconnect both the J1 and J2 harness connectors from the Engine ECM.
D. Check for continuity between th e following pins:
- Pin 1 on the 4-Pin aftertreatment cooling fan connector and pin 20 on the J1 ECM connector.
- Pin 3 on the 4-Pin aftertreatment cooling fan 12 on the J2 ECM connector.
- Pin 4 on the 4-Pin aftertreatment cooling fan connector and pin 11 on the J2 ECM connector.
Continuity
Result: There are less than 10 ohms of resistance on each wire.
Proceed to Test step 5.
Return to service.
Result: There are more than 10 ohms of resistance on each wire.
Repair: Repair the wiring or replace the wiring. Verify that the problem is resolved.
Return to service.
5. Perform an "ARD Ignition Test"
A. Turn the keyswitch to the ON position.
B. Connect Cat ET.
C. Use Cat ET to perform the "ARD Ignition Test".
D. Visually inspect the aftertreatment cooling fan after the first 30 seconds to see if it is operational.
Aftertreatment Cooling Fan
Result: The fan was not operational.
Repair: Replace the aftertreatment cooling fan.
The fan was operational.
Result: The aftertreatment cooling fan was shutdown due to high under hood temperatures. No repair is necessary. Return to service.
6. Check for an Open Circuit on the Fan Driver Circuit
A. Turn the keyswitch to the OFF position.
B. Disconnect the 4-pin wiring harness connector from the aftertreatment cooling fan.
C. Disconnect the engine ECM J1 connector.
D. Measure the resistance between the following pins:
- Pin 1 on the fan wiring harness connector and pin 20 on the J1 engine ECM wiring harness connector.
Open Circuit
Result: There was less than 10 Ohms of resistance between the pins.
Proceed to Test Step 7.
Result: There was more than 10 Ohms of resistance between

Cat SIS web machinery list:

Caterpillar parts catalog
966M Wheel Loader MD700001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader DZL00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader WGN00001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader R1Z00001-UP (MACHINE) POWERED BY C9.3 Engine
966H Wheel Loader Military RWE00001-UP (MACHINE) POWERED BY C11 Engine
IT38G II Integrated Toolcarrier CSX00001-UP (MACHINE) POWERED BY 3126B Engine
966L Wheel Loader FRS00001-UP (MACHINE) POWERED BY C9 Engine
972L Wheel Loader RFB00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader L8E00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader R8D00001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader B8P00001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader M5S00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader LMM00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader GGN00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader EJA00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader LSJ00001-UP (MACHINE) POWERED BY C9.3 Engine


Parts shim Caterpillar catalog:

6E1436 SHIM PACK
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 160M, 1...
4E3999 SHIM PACK
515, 518C, 525, 936F, 938F, 938G, 938G II, IT38F, IT38G, IT38G II
2V7390 SHIM PACK
518, 528, 528B, 530B, 611, 613C, 613C II, 613G, 615, 615C, 725, 725C, 730, 730C, 735, 735B, 740, 740B, 814B, 815B, 816B, 950B, 950B/950E, 966D, 966F, 966G, D25C, D25D, D300E, D300E II, D30C, D350C, D3...
4K7464 SHIM PACK
12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H ...
6W8246 SHIM PACK
924G, 924GZ, 924H, 924HZ, 924K, 926, 928F, 928G, 928H, 928HZ, 930G, 930K, 936, 938F, 938G, 938G II, 938H, 938K, CS-643, G936, IT28, IT28F, IT28G, IT38F, IT38G, IT38G II, IT38H, SH-56B
1188276 SHIM PACK
525B, 525C, 535B, 535C, 545, 545C, 824K, 825K, 826K, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, HA770, HA...
1376841 SHIM
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 844, 844H, 854G, 854K, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, ...
1590268 SHIM
938K, 950 GC, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
1590269 SHIM
938K, 950 GC, 950G, 950G II, 950H, 962G, 962G II, 962H, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972K, 972M, 972M XE
1V8848 SHIM PACK
525D, 535D, 545D, 555D, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE,...
1377668 SHIM PACK
824K, 825K, 826K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
3223111 SHIM PACK
814F, 814F II, 815F, 815F II, 816F, 816F II, 966H, 966K, 966M, 972H, 972K, 972M
1977264 SHIM
914G, IT14G, IT14G2
2180371 SHIM
623G, 623H, 623K, 623K LRC
3853608 SHIM
914G, IT14G, IT14G2
3853607 SHIM
914G, IT14G, IT14G2
3853606 SHIM
914G, IT14G, IT14G2
2341794 SHIM
924H, 928H, IT28G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.