2191370 SHIM Caterpillar parts
1190T, 1290T, 2391, 2491, 522, 522B, 532, 552, 552 2, TK722, TK732, TK752
Rating:
Alternative (cross code) number:
CA2191370
219-1370
2191370
CA2191370
219-1370
2191370
Weight: 0.20 pounds 0 kg.
TRACK FELLER BUNCHER,
Compatible equipment models: 2191370:
Number on catalog scheme:
22
For full view, you need register
Information:
MID 87 - Chassis ECMCID 378 - Machine Auto-Lube SolenoidFMI 6 - Current Above Normal
Illustration 1 g01827954
"Auto Lube" solenoid circuit
This diagnostic code indicates that the "Chassis ECM" detects the "Auto Lube" solenoid current is above normal.The following can cause this code:
Solenoid energizer circuit shorted to ground
Solenoid failure
ECM failureNote: The following test procedure may create other diagnostic codes. Ignore these created codes and clear these created codes after the original diagnostic code has been corrected. Ensure diagnostic code CID 378 FMI 6 is active before performing this procedure.Note: Use a calibrated digital multimeter for this procedure.System Response:
The ECM turns off current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn on the disconnect switch and the key switch.
Observe the status of the diagnostic code.
Disconnect from the harness the solenoid with the active diagnostic code.Expected Result:FMI 6 changes to FMI 5 after the solenoid is disconnected.Results:
OK - FMI 6 changes to FMI 5. The solenoid has failed.Repair: Replace the solenoid.STOP
NOT OK - FMI 6 does not change to FMI 5. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID ENERGIZE CIRCUIT FOR A SHORT TO GROUNDThe solenoid remains disconnected from the harness.
Turn off the key switch and the disconnect switch.
Disconnect the harness from the ECM.
At the harness connector, measure the resistance from the signal contact J2-3 (wire R816-PK(Pink)) to all contacts used in the harness connectors for the ECM.Expected Result:Each resistance is greater than 5000 ohms.Results:
OK - Each resistance is greater than 5000 ohms. Proceed to Test Step 3.
NOT OK - A resistance is less than 5000 ohms. There is a short between (wire R816-PK(Pink)) and the circuit with low resistance.Repair: Repair or replace the harness.STOPTest Step 3. CHECK THE DIAGNOSTIC CODE
Inspect the harness.Clean the harness connector contacts.Inspect the harness connector contacts for corrosion or damage.Inspect the wire insulation for damage caused by heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each circuit wire.
Reconnect all harness connectors.Verify that the connectors are fully seated and the clips are fastened.
Check for intermittent problems. Use Cat® Electronic Technician (Cat® ET) and perform a wiggle test on the harness.
Turn on the disconnect switch and the key switch.
Operate the machine.
Determine the diagnostic code status.Expected Result:The diagnostic code not is active.Results:
OK - The diagnostic code is not active.Repair: The initial diagnostic code was probably caused by a poor connection at one of the connectors that was checked.Resume normal operation.STOP
NOT OK - The diagnostic code is active. The ECM may have failed.Repair: Exit this procedure and perform this procedure again. Contact the technical communicator at your Caterpillar dealer. If the ECM requires replacement, see Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Illustration 1 g01827954
"Auto Lube" solenoid circuit
This diagnostic code indicates that the "Chassis ECM" detects the "Auto Lube" solenoid current is above normal.The following can cause this code:
Solenoid energizer circuit shorted to ground
Solenoid failure
ECM failureNote: The following test procedure may create other diagnostic codes. Ignore these created codes and clear these created codes after the original diagnostic code has been corrected. Ensure diagnostic code CID 378 FMI 6 is active before performing this procedure.Note: Use a calibrated digital multimeter for this procedure.System Response:
The ECM turns off current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn on the disconnect switch and the key switch.
Observe the status of the diagnostic code.
Disconnect from the harness the solenoid with the active diagnostic code.Expected Result:FMI 6 changes to FMI 5 after the solenoid is disconnected.Results:
OK - FMI 6 changes to FMI 5. The solenoid has failed.Repair: Replace the solenoid.STOP
NOT OK - FMI 6 does not change to FMI 5. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID ENERGIZE CIRCUIT FOR A SHORT TO GROUNDThe solenoid remains disconnected from the harness.
Turn off the key switch and the disconnect switch.
Disconnect the harness from the ECM.
At the harness connector, measure the resistance from the signal contact J2-3 (wire R816-PK(Pink)) to all contacts used in the harness connectors for the ECM.Expected Result:Each resistance is greater than 5000 ohms.Results:
OK - Each resistance is greater than 5000 ohms. Proceed to Test Step 3.
NOT OK - A resistance is less than 5000 ohms. There is a short between (wire R816-PK(Pink)) and the circuit with low resistance.Repair: Repair or replace the harness.STOPTest Step 3. CHECK THE DIAGNOSTIC CODE
Inspect the harness.Clean the harness connector contacts.Inspect the harness connector contacts for corrosion or damage.Inspect the wire insulation for damage caused by heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each circuit wire.
Reconnect all harness connectors.Verify that the connectors are fully seated and the clips are fastened.
Check for intermittent problems. Use Cat® Electronic Technician (Cat® ET) and perform a wiggle test on the harness.
Turn on the disconnect switch and the key switch.
Operate the machine.
Determine the diagnostic code status.Expected Result:The diagnostic code not is active.Results:
OK - The diagnostic code is not active.Repair: The initial diagnostic code was probably caused by a poor connection at one of the connectors that was checked.Resume normal operation.STOP
NOT OK - The diagnostic code is active. The ECM may have failed.Repair: Exit this procedure and perform this procedure again. Contact the technical communicator at your Caterpillar dealer. If the ECM requires replacement, see Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Caterpillar parts catalog:
Parts shim Caterpillar catalog:
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, ...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 311, 311B, 312, 312B, 313B, 320 L, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320D, 320E LN, 320N, 321D LCR, 322, 322 FM L, 322 L, 322 LN, 3...
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 311D LRR, 312D, 312E, 314D LCR, 314E LCR, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318D L, 318D2 L, 318E L, 320 L, 320B...
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 311D LRR, 312D, 312E, 314D LCR, 314E LCR, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318D L, 318D2 L, 318E L, 320 L, 320B...
1390, 2590, 315, 315B L, 317, 317B LN, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320D, 320E LN, 320N, 321D LCR, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 323D L, 323D LN, 323D SA, 323E L, 3...
1390, 2590, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, ...
1390, 2590, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307, 307B, 307C, 308C, 308E SR, 320C, 322, 322 FM L, 322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 3...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307, 307B, 307C, 308C, 308E SR, 320C, 322, 322 FM L, 322B, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D L, 325, 325 FM L, 325 L, 325 LN, ...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307, 307B, 307C, 320C, 322, 322 FM L, 325, 325 FM L, 325 L, 325 LN, 325B L, 325C, 325C FM, 325C L, 325D FM, 325D FM LL, 325D MH, 330, 330 ...
2384C, 2484C, 311B, 311C, 311D LRR, 311F LRR, 312B L, 312C, 312C L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D...
2343015
SHIM
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
2343014
SHIM
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
2343013
SHIM
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, TK711, TK721, TK722, TK732
2373417
SHIM
322C
322C
2373416
SHIM
322C
322C
2373415
SHIM
322C
322C
2254833
SHIM
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
2254832
SHIM
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
2254831
SHIM
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
2254830
SHIM
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D,...
2461765
SHIM
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
1390, 2590, 541, 541 2, 551, 552, 552 2, TK741, TK751, TK752
2455975
SHIM
1390, TK741, TK751, TK752
1390, TK741, TK751, TK752