4673265 SHIM Caterpillar parts
Rating:
Alternative (cross code) number:
CA4673265
467-3265
4673265
CA4673265
467-3265
4673265
Information:
Illustration 3 g02223675
Mount the 354-1384 Resistor Gp (1) to the 363-5991 Bracket As (3) with two 9X-2185 Screws . Refer to Illustration 3.
Mount the 133-9012 Fuse (2) to the 363-5991 Bracket As (3) with one 9X-2185 Screw .
Mount the 354-1384 Resistor Gp (1) to the HVAC unit with the existing bolts and washers. Refer to Illustration 3.
Illustration 4 g02184976
Use the following procedure to make a jumper wire to connect the number five terminal of the 354-1384 Resistor Gp (3) to the 133-9012 Fuse (1) :
Cut 200 mm (7.9 inch) of wire from the 5P-5621 Wire .
Strip the ends of the wire and crimp a 5P-5618 Blade Terminal on each end of the wire with 9S-9150 Terminal Crimp Tool As .
Cover each terminal with 70.0 mm (2.76 inch) of 6V-9023 Heat Shrink Tube .
Use the heat gun to shrink the tubing.
Connect one end of the jumper wire to the number five terminal and other end of the jumper wire to the 133-9012 Fuse (1) .
Bend the wire to the left of the resistor to prevent interference with the recirculation filter.
Illustration 5 g02334017
Use the following procedure to make a jumper wire to connect the 133-9012 Fuse (1) to the wire (515-GY) of the harness AC6 and the wire (579-BR) of the harness AC8:
Cut 400.0 mm (15.75 inch) of wire from the 5P-5621 Wire .
Strip the ends of the wire and crimp a 5P-5618 Blade Terminal on one end of the wire with 9S-9150 Terminal Crimp Tool As .
Cover the 5P-5618 Blade Terminal with 70.0 mm (2.76 inch) of 6V-9023 Heat Shrink Tube .
Use the heat gun to shrink the tubing.
Install the end of the jumper harness into the 133-9012 Fuse .
Slide 100 mm (4.0 inch) of 125-7876 Heat Shrink Tube onto the end of the wire with no connector.
Illustration 6 g02175985
Illustration 7 g02175986
Crimp a 2L-8067 Terminal to the end of the wire with no connector. Refer to Illustrations 6 and 7.
Cut off the existing connectors of the wire (515-GY) of the harness AC6 and the (579-BR) of the harness AC8.
Strip the wires and crimp a 2L-8067 Terminal onto each wire.
Place the 2L-8067 Terminal from the jumper wire between the 2L-8067 Terminal of the wire (515-GY) of the harness AC6 and the wire (579-BR) of the harness AC8. Refer to Illustration 5.
Secure the three terminals together with a 7X-2619 Bolt and 5C-2890 Nut .
Tighten the bolt and nut to 12 3 N m (8.8 2.2 lb ft). Refer to Illustration 6.
Slide the 125-7876 Heat Shrink Tube over the three terminals use the heat gun to shrink the tubing. Refer to Illustration 7
Bend the wire to the right of the resistor to prevent interference with the recirculation filter.
Install the remaining wires to the blower resistor assembly. Refer to Illustration 5.
The wire (516-GN) of the harness AC4 goes to terminal number two on the blower speed resistor.
The wire (517-BU) of the harness AC3 goes to terminal number
Parts shim Caterpillar catalog:
4673264
SHIM
Caterpillar
Caterpillar
4670871
SHIM-PACK
Caterpillar
Caterpillar
4670870
SHIM-PACK
Caterpillar
Caterpillar
4670837
SHIM
Caterpillar
Caterpillar
4670836
SHIM
Caterpillar
Caterpillar
4670691
SHIM-PACK
Caterpillar
Caterpillar
4675231
SHIM-RR SHAFT
Caterpillar
Caterpillar
4675214
SHIM-
Caterpillar
Caterpillar
4673269
SHIM
Caterpillar
Caterpillar
4673268
SHIM
Caterpillar
Caterpillar
4673267
SHIM
Caterpillar
Caterpillar
4673266
SHIM
Caterpillar
Caterpillar