AVSPARE.COM
parts catalog

SHIM 4Z8602 - Caterpillar



4Z8602 SHIM Caterpillar parts SHIM
Rating:
46
Alternative (cross code) number:
CA4Z8602
4Z-8602
4Z8602
Caterpillar 4Z8602 SHIM
Weight: 3 pounds 1 kg.

Buy SHIM 4Z8602 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Specification
Table 1
"Swing Speed and Swing Drift on a Slope"
Swing Time (seconds)
Item New Service Limit Actual
Right Swing 3.5 or less 4.2 or less
Left Swing
Swing Drift mm (inch)
Item New Service Limit Actual
Right Swing 0 0
Left Swing Introduction
Measuring the swing speed on a slope will determine if there is a need to check the swing motor and the anti-reaction valve. Measuring the swing drift on a slope will determine if there is a need to check the swing parking brake.Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".Required Tools
Table 2
Required Tools
Description Qty
Measuring Tape 1
Stopwatch 1 Test Procedure
Swing Speed on a Slope
Illustration 1 g00298078
Complete the following steps in order to measure the swing speed on a slope.
The work tool should be empty.
Position the machine on a slope of 12 degrees. Refer to Illustration 1.
Position the implements at maximum reach and close the work tool. Position the work tool above the ground so that the work tool will not come in contact with any obstacles.
Illustration 2 g00298079
Position the upper structure at position (A). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 2.
Measure the time that is required to swing the upper structure from position (A) to position (B).
Position the upper structure at position (C). The upper structure should be at a 90 degree angle to the lower structure.
Measure the time that is required to swing the upper structure from position (C) to position (B). Swing Drift on a Slope
Complete the following steps in order to measure the swing drift on a slope.
Illustration 3 g00298079
Position the upper structure at position (A). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 3.
Illustration 4 g00293972
(A) Upper frame
(B) Undercarriage frame
(C) Marking
To indicate the relationship of the two positions, put a mark (C) on the inner race and the outer race of the swing bearing. Refer to Illustration 4.
Stop the engine.
Leave the machine in this position for 3 minutes. Measure the swing drift on the circumference of the swing bearing.
Start the engine.
Position the upper structure at position (C). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 3.
Repeat Steps 1.b through 1.d.


Parts shim Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.