6D3364 SHIM (.010 IIN. THICK) Caterpillar parts
16
Rating:
Alternative (cross code) number:
CA6D3364
6D-3364
6D3364
CA6D3364
6D-3364
6D3364
Weight: 0.01 pounds 0 kg.
Information:
ID
30.226
mm
NUMBER OF PITCH HOLES+C190
4
OD
76.2
mm
PITCH CIRCLE DIAMETER
53.975
mm
PITCH CIRCLE HOLE DIAMETER
14.275
mm
MATERIAL THICKNESS
.254
mm
MOTOR GRADER,
Compatible equipment models: 6D3364:
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Locking Pin
Ø 8mm by 85mm 1
If the engine has guards, remove the guards. Refer to the OEM for the correct procedure. Note: Mark the direction of rotation of the alternator belt, if the belt will be reused.
Illustration 1 g02433716
Typical example
Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction.
Insert Tooling (A) into Hole (Y).
Remove alternator belt (1).
If necessary, Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction and remove Tooling (A) from Hole (Y).
Release the pressure on the 1/2" square drive tool and remove the 1/2" square drive tool from Hole (X). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Locking Pin
Ø 8mm by 85mm 1
Illustration 2 g02433716
Typical example
If necessary, follow Step 1.a through Step 1.c in order to position the tensioner correctly.
Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction.
Insert Tooling (A) into Hole (Y).
Release the pressure on the 1/2" square drive tool and remove the 1/2" square drive tool from Hole (X).
Clean all pulleys and guide rollers. Ensure that the pulleys and all guide rollers are clean. Ensure that the pulleys and guide rollers are free from dirt and build up from the old belt. Note: The grooves on the alternator belt must be located into the grooves of all pulleys.
Position alternator belt (1). Ensure that the alternator belt is centered on all pulleys. A used alternator belt should be installed in the original direction of rotation.
Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction. Remove Tooling (A) from Hole (Y).
Release the pressure on the 1/2" square drive tool until the alternator belt is tensioned. Remove the 1/2" square drive tool from Hole (X). Note: The tensioner should be at the nominal position.
If the engine has guards, install the guards. Refer to the OEM for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Locking Pin
Ø 8mm by 85mm 1
If the engine has guards, remove the guards. Refer to the OEM for the correct procedure. Note: Mark the direction of rotation of the alternator belt, if the belt will be reused.
Illustration 1 g02433716
Typical example
Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction.
Insert Tooling (A) into Hole (Y).
Remove alternator belt (1).
If necessary, Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction and remove Tooling (A) from Hole (Y).
Release the pressure on the 1/2" square drive tool and remove the 1/2" square drive tool from Hole (X). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Locking Pin
Ø 8mm by 85mm 1
Illustration 2 g02433716
Typical example
If necessary, follow Step 1.a through Step 1.c in order to position the tensioner correctly.
Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction.
Insert Tooling (A) into Hole (Y).
Release the pressure on the 1/2" square drive tool and remove the 1/2" square drive tool from Hole (X).
Clean all pulleys and guide rollers. Ensure that the pulleys and all guide rollers are clean. Ensure that the pulleys and guide rollers are free from dirt and build up from the old belt. Note: The grooves on the alternator belt must be located into the grooves of all pulleys.
Position alternator belt (1). Ensure that the alternator belt is centered on all pulleys. A used alternator belt should be installed in the original direction of rotation.
Install a 1/2" square drive tool into Hole (X) in tensioner (2). From the front of the engine, turn the tool in a clockwise direction. Remove Tooling (A) from Hole (Y).
Release the pressure on the 1/2" square drive tool until the alternator belt is tensioned. Remove the 1/2" square drive tool from Hole (X). Note: The tensioner should be at the nominal position.
If the engine has guards, install the guards. Refer to the OEM for the correct procedure.
Caterpillar parts catalog:
Parts shim Caterpillar catalog:
16, 24H, 24M, 30/30, 517, 527, 561H, 561M, 572G, 572R, 572R II, 578, 583R, 587R, 587T, 589, 594, 611, 613C, 613C II, 613G, 615, 615C, 621E, 621F, 623E, 631E, 637E, 65, 651, 651E, 657, 657E, 65C, 65E, ...
16, 24H, 24M, 30/30, 320C, 322C, 325C, 325D, 325D L, 325D MH, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336E, 336E HVG, 336E L, 336E LH, 33...
120G, 12F, 12G, 130G, 14E, 14G, 16, 163, 16G, 172, 173B, 183, 183B, 191, 215, 225, 235, 235D, 245, 245B, 325 L, 428, 46, 508, 525B, 535B, 545, 561C, 613B, 613C, 615, 615C, 621E, 621F, 621G, 621H, 623E...
120G, 12F, 12G, 130G, 140, 14E, 14G, 16, 163, 16G, 173B, 183, 183B, 191, 215, 225, 235, 235D, 245, 245B, 46, 525B, 535B, 545, 561C, 621, 621B, 621E, 621F, 623, 623B, 623E, 627B, 627E, 627F, 631C, 631E...
14E, 16, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 611, 613C II, 613G, 615C, 814B, 814F, 814F II, 81...
12E, 16, 44, 46, 613, 621, 621B, 623B, 627B, 630B, 631C, 633, 651, 666, 6A, 7A, 8 SR, 824C, 824S, 834B, 8A, 966C, 977, 988, D6D, D6E, D6E SR, D6G SR, D6G2 XL, D7F, D7G, D9G
120G, 12F, 12G, 130G, 140G, 14E, 16, 160G
6D9675
SHIM (.030" Thick)
14G, 16, 16G
14G, 16, 16G
5D0663
SHIM
12F, 14E, 16
12F, 14E, 16
14G, 16
2S0457
SHIM
16
16
5D2904
SHIM (.010" Thick)
16, 16G
16, 16G
5D2905
SHIM (.030" Thick)
16, 16G
16, 16G
5D5233
SHIM (.030" Thick)
16, 16G
16, 16G
5D5232
SHIM (.010" Thick)
16, 16G
16, 16G
6D3531
SHIM (.010" Thick)
14G, 16
14G, 16
6D3530
SHIM (.005" Thick)
14G, 16
14G, 16