7D2259 SHIM Caterpillar parts
769
Rating:
Alternative (cross code) number:
CA7D2259
7D-2259
7D2259
CA7D2259
7D-2259
7D2259
Weight: 1 pounds 0 kg.
TRUCK,
Compatible equipment models: 7D2259:
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2 Start By:
Remove the front housing.
Remove the flywheel housing.
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g00964659
Remove connecting rod caps (1) and crankshaft main bearing caps (2) .
Remove the thrust plates from the cylinder block.
Illustration 2 g00953328
Fasten Tooling (A) and a suitable lifting device to crankshaft (3). The weight of crankshaft (3) is approximately 79 kg (175 lb).
Remove crankshaft (3) .Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Illustration 3 g00953328
Fasten Tooling (A) and a suitable lifting device to crankshaft (3). The weight of crankshaft (3) is approximately 79 kg (175 lb). Align the timing marks and position crankshaft (3) in the cylinder block.
Apply clean engine oil to the thrust plates and install the thrust plates in the cylinder block.
Illustration 4 g00964659
Install connecting rod caps (1) and crankshaft main bearing caps (2) .
Tighten the bolts for connecting rod caps (1) by using the following procedure:
Tighten each bolt to a torque of 50 5 N m (37 3 lb ft).
Place an index mark on each bolt. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Tighten the bolts for crankshaft main bearing caps (2) by using the following procedure:
Tighten each bolt to a torque of 95 5 N m (70 4 lb ft).
Place an index mark on each bolt. Tighten each bolt for an additional 90 5 degrees (1/4 turn).End By:
Install the engine oil pump.
Install the flywheel housing.
Install the front housing.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2 Start By:
Remove the front housing.
Remove the flywheel housing.
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g00964659
Remove connecting rod caps (1) and crankshaft main bearing caps (2) .
Remove the thrust plates from the cylinder block.
Illustration 2 g00953328
Fasten Tooling (A) and a suitable lifting device to crankshaft (3). The weight of crankshaft (3) is approximately 79 kg (175 lb).
Remove crankshaft (3) .Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Illustration 3 g00953328
Fasten Tooling (A) and a suitable lifting device to crankshaft (3). The weight of crankshaft (3) is approximately 79 kg (175 lb). Align the timing marks and position crankshaft (3) in the cylinder block.
Apply clean engine oil to the thrust plates and install the thrust plates in the cylinder block.
Illustration 4 g00964659
Install connecting rod caps (1) and crankshaft main bearing caps (2) .
Tighten the bolts for connecting rod caps (1) by using the following procedure:
Tighten each bolt to a torque of 50 5 N m (37 3 lb ft).
Place an index mark on each bolt. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Tighten the bolts for crankshaft main bearing caps (2) by using the following procedure:
Tighten each bolt to a torque of 95 5 N m (70 4 lb ft).
Place an index mark on each bolt. Tighten each bolt for an additional 90 5 degrees (1/4 turn).End By:
Install the engine oil pump.
Install the flywheel housing.
Install the front housing.
Caterpillar parts catalog:
Parts shim Caterpillar catalog:
16, 24H, 24M, 30/30, 517, 527, 561H, 561M, 572G, 572R, 572R II, 578, 583R, 587R, 587T, 589, 594, 611, 613C, 613C II, 613G, 615, 615C, 621E, 621F, 623E, 631E, 637E, 65, 651, 651E, 657, 657E, 65C, 65E, ...
16, 24H, 24M, 30/30, 320C, 322C, 325C, 325D, 325D L, 325D MH, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336E, 336E HVG, 336E L, 336E LH, 33...
120G, 12F, 12G, 130G, 14E, 14G, 16, 163, 16G, 172, 173B, 183, 183B, 191, 215, 225, 235, 235D, 245, 245B, 325 L, 428, 46, 508, 525B, 535B, 545, 561C, 613B, 613C, 615, 615C, 621E, 621F, 621G, 621H, 623E...
215B, 215D, 225, 227, 235, 235B, 245, 572R, 572R II, 631E, 633D, 633E II, 637D, 637E, 651E, 657E, 69D, 735, 735B, 740, 740B, 769, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772B, 772G, 772G OEM...
120G, 12F, 12G, 130G, 140, 14E, 14G, 16, 163, 16G, 173B, 183, 183B, 191, 215, 225, 235, 235D, 245, 245B, 46, 525B, 535B, 545, 561C, 621, 621B, 621E, 621F, 623, 623B, 623E, 627B, 627E, 627F, 631C, 631E...
12E, 140, 225, 245, 325 L, 41, 518, 518C, 528, 528B, 530B, 613, 613B, 613C, 613C II, 615, 615C, 621, 621B, 621E, 621F, 621G, 621H, 621K, 623, 623B, 623E, 623F, 623G, 623H, 627, 627B, 627E, 627F, 627G,...
1T0306
SHIM (.010"THICK)
16, 651, 657, 666, 768B, 769, 772, 773
16, 651, 657, 666, 768B, 769, 772, 773
769, 824, 824B, 825B, 826B, 834, 988, 988B
6D1248
SHIM
768B, 769, 772, 773
768B, 769, 772, 773
6D1248
SHIM
768B, 769, 772, 773
768B, 769, 772, 773
7D3346
SHIM
772, 773
772, 773
5D2519
SHIM
769, 773
769, 773
7D3478
SHIM
773
773
7D3479
SHIM
773
773
5D4148
SHIM
769, 773
769, 773
2P3692
SHIM (.003 in. Thick)
768B, 769, 772
768B, 769, 772
7M8378
SHIM PACK
769
769
9M9724
SHIM
768B, 769
768B, 769
5D7804
SHIM (.010" Thick)
769, 773
769, 773
5D7803
SHIM (.005" Thick)
769, 773
769, 773
6D0046
SHIM
768B, 768C, 769
768B, 768C, 769