AVSPARE.COM
parts catalog

SHIM 8D6541 - Caterpillar


8D6541 SHIM Caterpillar parts 14G, 14H, 14H NA
Rating:
23
Alternative (cross code) number:
CA8D6541
8D-6541
8D6541
Caterpillar 8D6541 SHIM
Weight: 0.01 pounds 0 kg.

Buy SHIM 8D6541 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compatible equipment models: 8D6541:

MOTOR GRADER  14G   14H   14H NA   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Table 1
Codes That Relate to Configuration Parameters
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
630-2 268-2 Programmed Parameter Fault : Erratic, Intermittent, or Incorrect The engine Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed.
The ECM may use a default torque map or the ECM may limit the engine to low idle.
The code is active only.
Follow the troubleshooting procedure to identify the root cause of the problem. The electronic service tool can be used to view certain parameters that can affect the operation of the engine. The electronic service tool can also be used to change certain parameters. Some parameters cannot be changed and some applications do not allow any changes to the programmable monitoring system. The parameters are stored in the Electronic Control Module (ECM). Some of the parameters are protected from unauthorized changes by passwords. Parameters that can be changed have a tattletale number. The tattletale number shows if a parameter has been changed.The parameters are divided into two different types:Customer Specified Parameters - Customer passwords may be required to change the values of customer specified parameters.System Configuration Parameters - System configuration parameters affect the emissions of the engine or the power of the engine. Factory passwords may be required to change the values of system configuration parameters.
Illustration 1 g03747092
Typical configuration screen
Connect to the electronic service tool.
Select the Service tab.
Select the Configuration tab to view the configuration parameters.If an ECM is replaced, the appropriate parameters must be copied from the old ECM. Copy the parameters with the "Copy Configuration" feature of the electronic service tool. The "Copy Configuration" tab is below the "Configuration" tab. Alternatively, the settings can be recorded on paper and then programmed into the configuration screen for the new module.
Changing the parameters during engine operation can cause the engine to operate erratically and can cause engine damage.Only change the settings of the parameters when the engine is STOPPED.
Check Programmable Parameters 630-2 (268-2)
Illustration 2 g03747100
Typical active diagnostic codes screen
If a programmable parameter has not been programmed, the ECM will generate a 630-2 (268-2) diagnostic code. The programmable parameter that is not programmed will be listed under the code. Illustration 1 shows the parameters that are not programmed under the 630-2 (268-2) code. The unprogrammed parameters will be set to default. Certain aspects of the engines performance and engine monitoring may be affected.If "Injector Trim" is displayed below a 630-2 (268-2) diagnostic code on the electronic service tool, refer to Troubleshooting, "Injector Code - Calibrate".

Caterpillar parts catalog:

Caterpillar parts catalog
14G Motor Grader 96U07046-UP (MACHINE) POWERED BY 3306 Engine
14H Motor Grader 7WJ00001-UP (MACHINE) POWERED BY 3306 Engine
14H Motor Grader ASE00001-UP (MACHINE) POWERED BY 3176C Engine


Parts shim Caterpillar catalog:

7B5531 SHIM (.014" THICK)
120G, 12G, 130G, 140G, 14G, 14H NA, 160G, 561B, 977D, 977H
4K7464 SHIM PACK
12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H ...
4K7465 SHIM PACK
14G, 14H, 14H NA, 14M, 814, 814B, 814F, 814F II, 815, 815B, 815F, 815F II, 816F, 816F II, 966C, 966D, 966F, 966F II, 970F
2G2946 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA, 16M, AP-1055B, BG-2455C, BG-245C
9T9071 SHIM
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
7D8983 SHIM
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
7D8984 SHIM
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
6G5543 SHIM
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, 16H NA, 24M
2G2945 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA, 16M
6G4642 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA, 24H
6G4643 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA, 24H
6J1882 SHIM
14G, 14H, 14H NA
2G3867 SHIM
14G, 14H, 14H NA, 14M
8W6591 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA
2P4468 SHIM PACK
14G, 14H, 14H NA, 16G, 16H, 16H NA
6G3213 SHIM PACK
14G, 14H, 14H NA
8D4813 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA
2G2945 SHIM
14G, 14H, 14H NA, 16G, 16H, 16H NA, 16M
2G9104 SHIM
14G, 14H, 14H NA
6J1881 SHIM
14G, 14H, 14H NA
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.