AVSPARE.COM
parts catalog

SHOE 0960240 - Caterpillar


0960240 SHOE Caterpillar parts E110, E110B, E120, E120B
Rating:
81
Alternative (cross code) number:
CA0960240
096-0240
0960240
Caterpillar 0960240 SHOE
Weight: 29 pounds 13 kg.
Information:
BOLT HOLE SIZE  24  mm
BOLT HOLE SPACING A  0  mm
BOLT HOLE SPACING B  60.32  mm
BOLT HOLE SPACING C  107.94  mm
WIDTH  500  mm

Buy SHOE 0960240 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 0960240:

EXCAVATOR  E110   E110B   E120   E120B   Caterpillar
Number on catalog scheme: 16
  For full view, you need register

Information:


Illustration 1 g01069512
Schematic of the hoist proportioning solenoid - raise
This diagnostic code is associated with the hoist proportioning solenoid - raise. The diagnostic code is recorded when the Power Train/Chassis Electronic Control Module (ECM) reads the current of the solenoid as being below normal.The possible causes are listed:
There is an open in the circuit.
The solenoid has failed.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0724 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:The hoist proportioning solenoid - raise is always de-energized. The body does not go up. The body will return to the down position. When the diagnostic code is active, and the hoist control lever is moved to the RAISE position, the hoist system will remain in the HOLD position. The hoist system will remain in the HOLD position until the hoist control lever is returned to the HOLD position. The hoist system will operate properly after the diagnostic code has been corrected.Test Step 1. CHECK THE SOLENOID.
Turn the battery disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the machine harness from the solenoid.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire G704-YL(Yellow)) to contact 2 (wire E790-PK(Pink)).
Observe the status of the diagnostic code. Expected Result:The diagnostic code is active. Then, the diagnostic code is not active as the jumper wire is installed and removed. Results:
YES - The circuit is correct. The solenoid has failed.Repair: Repeat this test "CHECK THE SOLENOID" in order to verify that the solenoid has failed. Replace the solenoid.STOP
NO - The diagnostic code remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID CIRCUIT FOR AN OPEN.
Turn the key start switch and the battery disconnect switch to the OFF position.
Disconnect the J2 machine harness connector from the ECM.
At the machine harness connector for the solenoid, the jumper wire remains installed.
At J2 machine harness connector, measure the resistance from contact J2-3 (wire E790-PK(Pink)) to J2-13 (wire G704-YL(Yellow)). Expected Result:The resistance should be less than 5 ohms.Results:
YES - The resistance is less than 5 ohms. The machine harness is correct. Proceed to Test Step 3.
NO - The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in the wire for the solenoid signal or in (wire E790-PK(Pink)) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all the harness connectors.
Turn the battery disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0724 FMI 05. Expected Result:The CID 0724 FMI 05 is active. Results:
YES

Caterpillar parts catalog:

Caterpillar parts catalog
E120 HYDRAULIC EXCAVATOR 1LF00001-UP (MACHINE) POWERED BY 6D14 ENGINE
E110 HYDRAULIC EXCAVATOR 3FG00001-UP (MACHINE) POWERED BY 4D31-T ENGINE
E120B EXCAVATOR-TRACK TYPE 7NF00001-UP (MACHINE) POWERED BY S4K-T ENGINE
E110B TRACK TYPE EXCAVATOR 9HF00001-UP (MACHINE) POWERED BY S4K-T ENGINE
E120B TRACK-TYPE EXCAVATOR 4XK00001-UP (MACHINE) POWERED BY 3114 ENGINE
E110B TRACK-TYPE EXCAVATOR 5GK00001-UP (MACHINE) POWERED BY 3114 ENGINE


Parts shoe Caterpillar catalog:

0960231 SHOE-TRACK
312, 312C L, E110B, E120, E120B, E140
0931939 SHOE
E110, E110B, E120, E120B
0931940 SHOE
E110, E110B, E120, E120B
0931941 SHOE
E110, E110B, E120, E120B
0960255 SHOE
E110B, E120, E120B
0960255 SHOE
E110B, E120, E120B
0931941 SHOE
E110, E110B, E120, E120B
0931940 SHOE
E110, E110B, E120, E120B
0931939 SHOE
E110, E110B, E120, E120B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.