SHOE-TRACK 1Q4610 - Caterpillar

1Q4610 SHOE-TRACK Caterpillar parts 963C

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1Q4610
1Q-4610
1Q4610

Weight: 36 pounds 16 kg.

Information:

BOLT HOLE SIZE 19.38 mm

BOLT HOLE SPACING A 19.05 mm

BOLT HOLE SPACING B 133.35 mm

BOLT HOLE SPACING C 76.2 mm

BOLT HOLE SPACING D 37.08 mm

PITCH 203 mm

WIDTH 450 mm

Buy SHOE-TRACK 1Q4610 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Compatible equipment models: 1Q4610:

TRACK LOADER 963C Caterpillar

Number on catalog scheme: 2

Caterpillar 1Q4610 Parts scheme SHOE-TRACK

For full view, you need register

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

963C Track-Type Loader LGP 2DS00001-UP (MACHINE) POWERED BY 3116 Engine

1Q-4611: TRACK GP » SEBP26390377

963C TRACK-TYPE LOADER TIER II BBD00001-UP (MACHINE) POWERED BY 3126B Engine

230-6172: TRACK GP » SEBP31690477

963D TRACK-TYPE LOADER LCS00001-UP (MACHINE) POWERED BY C6.6 Engine

363-5923: TRACK GP » SEBP44560519

963K TRACK-TYPE LOADER LBL00001-UP (MACHINE) POWERED BY C7.1 Engine

363-5923: TRACK GP » SEBP72350439

Information:

Table 1
J1939 Code and Description Comments
4335-15
Aftertreatment #1 SCR Dosing Air Assist Absolute Pressure : High - least severe (1) The air pressure is above the trip point for the programmed delay time.
Dosing is disabled until the pressure is correct.
The code is logged.
Table 2
Associated Codes
J1939 Code CDL Code Troubleshooting Procedure
4335-3 3092-3 Troubleshooting, "Sensor Signal (Analog, Active) - Test"
4335-4 3092-4 Troubleshooting, "Sensor Signal (Analog, Active) - Test"
4336-5 3094-5 Troubleshooting, "Solenoid Valve - Test"
4336-6 3094-6 Troubleshooting, "Solenoid Valve - Test" Probable Causes
Codes
Air pressureRecommended Actions
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Turn the DC breaker to the ON position.
B. Connect Cat® Electronic Technician (ET) to the service tool connector.
C. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check the Air Supply to the Dosing Cabinet
A. Turn the DC breaker to the OFF position.
B. Disconnect the air supply line to the dosing cabinet.
C. Install a pressure gauge on the air supply line to the dosing cabinet.
D. Monitor the air supply pressure from the air compressor.
E. Reconnect the air supply line to the dosing cabinet.
483 kPa to 1068 kPa (70 psi to 155 psi)
Result: The air supply pressure from the air compressor is 483 kPa to 1068 kPa (70 psi to 155 psi).
Proceed to Test Step 4.
Result: The air supply pressure from the air compressor is greater than 1068 kPa (155 psi).
Repair: There is a problem with the air supply to the dosing cabinet. For information on the air compressor, refer to the Original Equipment Manufacturers (OEM) service information.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Air Pressure
A. Turn the DC breaker to the ON position.
B. Connect Cat ET.
C. Use Cat ET to perform the following override:
- Set the "Aftertreatment #1 SCR Dosing Air Assist Valve Command Override" to the ON position.
D. Use Cat ET to monitor the following pressure:
- "Aftertreatment #1 Supply Air Pressure"
414 kPa to