3A8962 SHOE-TRACK Caterpillar parts
312, 312B L, 312C, 312D
Rating:
Alternative (cross code) number:
CA3A8962
3A-8962
3A8962
CA3A8962
3A-8962
3A8962
Weight: 25 pounds 11 kg.
Information:
BOLT HOLE SIZE
16.21
mm
BOLT HOLE SPACING A
0
mm
BOLT HOLE SPACING B
108
mm
BOLT HOLE SPACING C
60.4
mm
BOLT HOLE SPACING D
0
mm
PITCH
170.7
mm
WIDTH
500
mm
EXCAVATOR,
Number on catalog scheme:
2
For full view, you need register
Information:
Installation Procedure of the Hose Assembly
Illustration 1 g01230674
Remove old 162-2501 Hose As (1). Keep all of the manifold and pump fittings attached.Note: Step 2 is only for 3408E engines.
Remove the 7W-6492 Pipe Plug (2) from the aftercooler housing (3). Install the 8T-6762 Pipe Plug into the aftercooler housing.
Illustration 2 g01230678
Note: Always tighten the fittings with your hand before you use a wrench. Support the hose and the elbow while you tighten in order to avoid the following damage: twisting, kinking and side loading.
Loosen elbow (4) and jam nut (5) .
Hand tighten the nut on the hose (5) to the elbow (4) .
Install the other end of the hose (6) to the pump fitting. Tighten the nut to 125 15 N m (90 11 lb ft).
Hold the elbow (4) in position and torque the jam nut to 145 15 N m (105 11 lb ft).
Support the elbow (4). Tighten the nut (5) on the hose to 125 15 N m (90 11 lb ft).
Illustration 3 g01230687
Illustration 3 shows the routing of the 162-2501 Hose As (8). The hose is routed from the rail, around the rear of the fuel transfer pump (9), and into the 90 degree fitting (7) that is installed into the pump.
Illustration 4 g01230689
Some 3408 engines use an aftercooler that is mounted high. The mounting bracket (10) is located close to the 162-2501 Hose As (8). If there is not enough clearance to install the protective sleeve, the hose will need to be loosened and the hose will need to be repositioned. Refer to 5 for repositioning of the hose.
Illustration 5 g01230690
The hose must be realigned if any of the following conditions exist:
Not enough clearance against the fuel transfer pump
Not enough clearance against the support bracket
Loosen the end of the hose (12) .
Loosen the elbow and the jam nut (11). Note: Do not remove the hose.
Reposition the hose in order to acquire the desired clearance.
Hold the end of the hose (12). Tighten the jam nut (11) .Tighten the jam nut to the following torque. ... 143 15 N m (105 11 lb ft)Note: Locking pliers can be used on the crimped portion of the hose. Do not use the locking pliers on the braided portion of the hose. This will damage the hose which will cause a failure.
Tighten the end of the hose (12) .Tighten the end of the hose to the following torque. ... 125 15 N m (92 11 lb ft)Note: If adjustment of the hose is required, make sure that the hose is not bent. Also, ensure that the hose is not twisted. If these conditions exist the PTFE liner can be damaged.Installation of the Protective Sleeve Over the New Hose Assembly
Illustration 6 g01106118
Top viewInstallation of a protective sleeve for the hoses of the pumps (1) of the HEUI Fuel System is now used. If this hose fails, there is a possibility that fuel could spray onto hot engine parts. A leak can be
Illustration 1 g01230674
Remove old 162-2501 Hose As (1). Keep all of the manifold and pump fittings attached.Note: Step 2 is only for 3408E engines.
Remove the 7W-6492 Pipe Plug (2) from the aftercooler housing (3). Install the 8T-6762 Pipe Plug into the aftercooler housing.
Illustration 2 g01230678
Note: Always tighten the fittings with your hand before you use a wrench. Support the hose and the elbow while you tighten in order to avoid the following damage: twisting, kinking and side loading.
Loosen elbow (4) and jam nut (5) .
Hand tighten the nut on the hose (5) to the elbow (4) .
Install the other end of the hose (6) to the pump fitting. Tighten the nut to 125 15 N m (90 11 lb ft).
Hold the elbow (4) in position and torque the jam nut to 145 15 N m (105 11 lb ft).
Support the elbow (4). Tighten the nut (5) on the hose to 125 15 N m (90 11 lb ft).
Illustration 3 g01230687
Illustration 3 shows the routing of the 162-2501 Hose As (8). The hose is routed from the rail, around the rear of the fuel transfer pump (9), and into the 90 degree fitting (7) that is installed into the pump.
Illustration 4 g01230689
Some 3408 engines use an aftercooler that is mounted high. The mounting bracket (10) is located close to the 162-2501 Hose As (8). If there is not enough clearance to install the protective sleeve, the hose will need to be loosened and the hose will need to be repositioned. Refer to 5 for repositioning of the hose.
Illustration 5 g01230690
The hose must be realigned if any of the following conditions exist:
Not enough clearance against the fuel transfer pump
Not enough clearance against the support bracket
Loosen the end of the hose (12) .
Loosen the elbow and the jam nut (11). Note: Do not remove the hose.
Reposition the hose in order to acquire the desired clearance.
Hold the end of the hose (12). Tighten the jam nut (11) .Tighten the jam nut to the following torque. ... 143 15 N m (105 11 lb ft)Note: Locking pliers can be used on the crimped portion of the hose. Do not use the locking pliers on the braided portion of the hose. This will damage the hose which will cause a failure.
Tighten the end of the hose (12) .Tighten the end of the hose to the following torque. ... 125 15 N m (92 11 lb ft)Note: If adjustment of the hose is required, make sure that the hose is not bent. Also, ensure that the hose is not twisted. If these conditions exist the PTFE liner can be damaged.Installation of the Protective Sleeve Over the New Hose Assembly
Illustration 6 g01106118
Top viewInstallation of a protective sleeve for the hoses of the pumps (1) of the HEUI Fuel System is now used. If this hose fails, there is a possibility that fuel could spray onto hot engine parts. A leak can be
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
1168592
SHOE
3054, 312, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-200B, PS-300B, TH103, TH62, TH63, TH82, TH83
3054, 312, AP-800C, BG-225B, CB-534B, CB-534C, CB-535B, CP-433C, CS-431C, PS-200B, PS-300B, TH103, TH62, TH63, TH82, TH83
9W9349
SHOE-TRACK
312, 315, 315B L, 317, 320, 320 L, 320B, 320N, OEMS
312, 315, 315B L, 317, 320, 320 L, 320B, 320N, OEMS
312, 315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320D L, 320D LN, 320E LN, 323D LN, 323E L, OEMS
1171771
SHOE-TRACK
312, 312B L, 312C
312, 312B L, 312C
312, 312B L, 312C, 312D
3A8968
SHOE-TRACK
312, 312B L, 312C, 312D
312, 312B L, 312C, 312D
3A8969
SHOE-TRACK
312, 312B L, 312C
312, 312B L, 312C
1585057
SHOE-TRACK MASTER
312B L, 312C
312B L, 312C
1807824
SHOE-TRACK
312B L, 312C
312B L, 312C
8E4427
SHOE-TRACK
235C, 235D, 973C
235C, 235D, 973C
6Y6407
SHOE-TRACK
227, 231D
227, 231D
9W6727
SHOE-TRACK
219D, 225D, 229
219D, 225D, 229
3T8491
SHOE-TRACK
245B, 245D
245B, 245D
9G7111
SHOE-TRACK
245B, 245D
245B, 245D
315, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 318E L, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E ...
315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320D, 320D GC, 320D L, 320D...
315, 320, 320 L, 320B, 320C, E200B, OEMS
3A8969
SHOE-TRACK
312, 312B L, 312C
312, 312B L, 312C
3A8968
SHOE-TRACK
312, 312B L, 312C, 312D
312, 312B L, 312C, 312D
312, 312B L, 312C, 312D