SHOE-MASTER TRACK 3Y7652 - Caterpillar

Illustration 6 g01069173
Stacked components (2) 240-8149 Modular Handle Gp (3) Joystick handle cable (16) 235-6351 Boot (18) 235-6355 Plate (19) 190-8478 Rocker Switch (PARKING BRAKE) (20) 235-6352 Cover
Insert the joystick handle cable (3) through the following components (in the order given, starting with the boot):
235-6351 Boot (16)
235-6355 Plate (18)
235-6352 Cover (20)
237-4040 Grommet (5)
Illustration 7 g01069090
3E-3388 Receptacle As . (22) Pin 4, WH-20, Horn Common, Sw 3 (23) Pin 3, BR-20, Horn N/O, Sw 3 (24) Pin 2, GN-20, Accelerate N/C, Sw 2 (25) Pin 1, BK-20, Accelerate/Decelerate Common, Sw 1 and Sw 2 (26) Pin 5, YL-20, Decelerate N/C, Sw1 (27) Pin 6, BU-20, Decelerate N/O, Sw 1 (28) Pin 7, RD-20, Accelerate N/O, Sw 2 (29) Pin 8, Plugged ( 8T-8737 Seal Plug ) (30) 3E-3389 Receptacle Lock Wedge (31) 3E-3388 Receptacle As
Install the seven wire ends into the 3E-3388 Receptacle As . Refer to Illustration 7.
Insert the four 235-6354 Spacers (6) between the 230-1024 Electronic Control Gp (14) and the 235-6356 Bracket As (7). Refer to Illustration 2.
Use four 244-6822 Bolts (8) to attach the 230-1024 Electronic Control Gp (14) to the 235-6356 Bracket As (7) .Note: One of the four 244-6822 Bolts (8) also attaches the 156-6175 Clip (9) to the 235-6356 Bracket As (7). Refer to Illustration 2 for location and orientation.
Install the 245-7483 Grommet (4) over the joystick adapter. Refer to Illustration 3.
Illustration 8 g01061830
Joystick handle, cable, adapter, and adapter pin hole. Boot, plate, and cover not shown in order to display cable routing. (2) 240-8149 Modular Handle Gp (3) Joystick handle cable (14) Joystick adapter (22) Pin hole
Place the joystick handle (2) over the adapter (14). Route the joystick handle cable (3) as shown in Illustration 3. When routing the cable, ensure that the cable is routed without pinch or abrasion points.Note: Ensure that there is 150 10 mm (5.90 0.40 inch) of harness cable between the joystick handle and the grommet. Refer to Illustration 2 and Illustration 3.
Insert the 117-8683 Spring Pin into the hole at the bottom of the handle and into the hole in the shaft. Refer to Illustration 9.
Illustration 9 g01062334
(2) 240-8149 Modular Handle Gp (22) 117-8683 Spring Pin
Use a 7K-1181 Cable Strap (10) to secure the joystick handle cable to the 156-6175 Clip (9). Refer to Illustration 4.
Illustration 10 g01062330
(12) 6-pin connector - base (13) 8-pin connector - handle (21) Machine harness
Connect the 6-pin connector (12) and the 8-pin connector (13) to the machine harness (21) .
Use four 9X-2042 Screws and the 235-6355 Plate to secure the 235-6351 Boot and the 235-6352 Cover to the 235-6356 Bracket As .
Illustration 11 g01061798
(10) 7K-1181 Cable Straps (23) Harness
Use 7K-1181 Cable Straps (10) to reattach the wiring harness to the machine (Illustration 11).
Using Caterpillar ET, perform the joystick portion of the calibration procedure that