6D0552 SHOE AND LINING ASSEM. Caterpillar parts
120, 14E
Rating:
Alternative (cross code) number:
CA6D0552
6D-0552
6D0552
CA6D0552
6D-0552
6D0552
Weight: 8 pounds 4 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$74.50
25 Sep 2023
Amazon.com
CTP 6D0552 Shoe Lining & Band for Model 112E/F
CTP For Model 112E/F || Highly Efficient || Easy in-and-out fit
CTP For Model 112E/F || Highly Efficient || Easy in-and-out fit
$70.55
19 Jun 2023
Amazon.com
CTP 6D0552 Shoe Lining & Band for Model 112E/F
CTP For Model 112E/F || Highly Efficient || Easy in-and-out fit
CTP For Model 112E/F || Highly Efficient || Easy in-and-out fit
$86.81
23 Feb 2023
Amazon.com
CTP 6D0552 Shoe Lining & Band for Model 112E/F
CTP For Model 112E/F || Highly Efficient || Easy in-and-out fit
CTP For Model 112E/F || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
4
For full view, you need register
Information:
The following procedure describes the adjustments that are required if an engine speed-timing calibration is performed. After this procedure has been completed, the engine can be started and the engine can be run at rated speed.Note: This procedure does not include the instructions for performing the actual calibration.Note: Before changing any value per this procedure, record the original value.
Stop the engine.
If a device such as a load share module is supplying the PWM signal in order to bias the engine speed, then disconnect the wires from the device. Go to Step 4. If there is not a device that is supplying the PWM signal and the engine speed bias is controlled from the OCP, then go to Step 3.
Use the OCP control panel in order to idle the engine. Refer to the information for the idle speed and rated speed that is in the System Operation, "Voltage and Frequency Adjustment" section of this publication. Proceed to Step 5.
Set the "Engine Start Fault Protection Activation Delay Time" setpoint in the OCP to 90 seconds. Use Cat ET in order to set the "Secondary Desired Speed Input Configuration" set point in the engine ECM to "DISABLED".
Start the engine and run the engine at idle speed.
Perform the engine speed timing calibration.
Stop the engine.
Use Cat ET in order to return the set points that were modified in Step 2 through Step 4 to the original values. Navigate to the "Control" screen. Next, proceed to the "Rated" screen.
Reconnect any wires that were disconnected in Step 2.
Stop the engine.
If a device such as a load share module is supplying the PWM signal in order to bias the engine speed, then disconnect the wires from the device. Go to Step 4. If there is not a device that is supplying the PWM signal and the engine speed bias is controlled from the OCP, then go to Step 3.
Use the OCP control panel in order to idle the engine. Refer to the information for the idle speed and rated speed that is in the System Operation, "Voltage and Frequency Adjustment" section of this publication. Proceed to Step 5.
Set the "Engine Start Fault Protection Activation Delay Time" setpoint in the OCP to 90 seconds. Use Cat ET in order to set the "Secondary Desired Speed Input Configuration" set point in the engine ECM to "DISABLED".
Start the engine and run the engine at idle speed.
Perform the engine speed timing calibration.
Stop the engine.
Use Cat ET in order to return the set points that were modified in Step 2 through Step 4 to the original values. Navigate to the "Control" screen. Next, proceed to the "Rated" screen.
Reconnect any wires that were disconnected in Step 2.
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
120, 120B, 12E, 140, 140B
120, 120B, 120G, 140
120, 120B, 12E, 140
120, 120B, 12E, 140
4D3857
SHOE
14E
14E
5D6200
SHOE
14E
14E
5D3257
SHOE AND LINING ASSEM.
120, 14E
120, 14E
3480437
SHOE-TRACK
323D L
323D L
1210137
SHOE-TRACK
325 L, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E LN
325 L, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E LN
1210138
SHOE-TRACK
325 L, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 329E L, 329E LN
325 L, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 329E L, 329E LN
3012285
SHOE-TRACK
385C, 385C L, 385C L MH, 390D, 390D L, 390F L
385C, 385C L, 385C L MH, 390D, 390D L, 390F L
3012283
SHOE-TRACK
385C, 385C L, 390D, 390D L, 390F L
385C, 385C L, 390D, 390D L, 390F L
1504770
SHOE-TRACK
330D L, 330D MH, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG
330D L, 330D MH, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG
5D0538
SHOE
12F, 12G, 130G, 140G
12F, 12G, 130G, 140G
120, 120B, 12E, 140
120, 120B, 12E, 140
120, 120B, 120G, 140
120, 120B, 12E, 140, 140B