6G4526 SHOE-CIRCLE GUIDE Caterpillar parts
120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 160G
Rating:
Alternative (cross code) number:
CA6G4526
6G-4526
6G4526
CA6G4526
6G-4526
6G4526
Weight: 27 pounds 12 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$134.03
19 Jan 2022
US: Florida-Parts-Z
3192228 - Shoe-Circle 6G4526 fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Compatible equipment models: 6G4526:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A (1)     9U-6198     Crankshaft Turning Tool     1    
A (2)     5P-7306     Housing     1    
5P-7305 Engine Turning Tool     1    
B     136-4632     Timing Pin (Crankshaft)     1    
C     364-9107     Timing Pin (Fuel Injection Pump)     1    
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the wiring harness is correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g01967538
If necessary, use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check". Use Tooling (B) in order to lock the crankshaft so that number one piston is at top dead center position.
If necessary, install Tooling (C) in order to lock the fuel injection pump in the correct position.
Position a new gasket (17) (not shown) onto front housing (16) .
Position bolt (15) and spacer (14) onto fuel injection pump (10) .
Carefully install fuel injection pump (10) to front housing (16) . Ensure that the bore in the front housing (16) is not damaged as the fuel injection pump is installed.Note: The fuel injection pump should be supported by hand as the nuts and bolts are installed.
Tighten bolt (15) for fuel injection pump (10) finger tight.
Install nut (13) to fuel injection pump (10) finger tight.
Install new bolts (18) to fuel injection pump (10) finger tight.
Tighten bolts (18) and bolts (15) to a torque of 22 N m (195 lb in).Tighten nut (13) to a torque of 22 N m (195 lb in).
Illustration 2 g01967536
Remove Tooling (C) from fuel injection pump (10) . Install a new O-ring seal (9) (not shown) to plug (8) .
Remove Tooling (B) from the cylinder block. Install a new O-ring seal to the plug for the cylinder block. Install the plug to the cylinder block. Tighten the plug to a torque of 21 N m (186 lb in).
Install plug (8) to fuel injection pump (10) . Tighten the plug to a torque of 14 N m (124 lb in).
Remove the appropriate caps in order to install fuel injection
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A (1)     9U-6198     Crankshaft Turning Tool     1    
A (2)     5P-7306     Housing     1    
5P-7305 Engine Turning Tool     1    
B     136-4632     Timing Pin (Crankshaft)     1    
C     364-9107     Timing Pin (Fuel Injection Pump)     1    
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the wiring harness is correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g01967538
If necessary, use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Fuel Injection Timing - Check". Use Tooling (B) in order to lock the crankshaft so that number one piston is at top dead center position.
If necessary, install Tooling (C) in order to lock the fuel injection pump in the correct position.
Position a new gasket (17) (not shown) onto front housing (16) .
Position bolt (15) and spacer (14) onto fuel injection pump (10) .
Carefully install fuel injection pump (10) to front housing (16) . Ensure that the bore in the front housing (16) is not damaged as the fuel injection pump is installed.Note: The fuel injection pump should be supported by hand as the nuts and bolts are installed.
Tighten bolt (15) for fuel injection pump (10) finger tight.
Install nut (13) to fuel injection pump (10) finger tight.
Install new bolts (18) to fuel injection pump (10) finger tight.
Tighten bolts (18) and bolts (15) to a torque of 22 N m (195 lb in).Tighten nut (13) to a torque of 22 N m (195 lb in).
Illustration 2 g01967536
Remove Tooling (C) from fuel injection pump (10) . Install a new O-ring seal (9) (not shown) to plug (8) .
Remove Tooling (B) from the cylinder block. Install a new O-ring seal to the plug for the cylinder block. Install the plug to the cylinder block. Tighten the plug to a torque of 21 N m (186 lb in).
Install plug (8) to fuel injection pump (10) . Tighten the plug to a torque of 14 N m (124 lb in).
Remove the appropriate caps in order to install fuel injection
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
8H1141
SHOE-POLE
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
7X1950
SHOE-POLE
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 214B, 224B, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 3...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 214B, 224B, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 3...
5D0538
SHOE
12F, 12G, 130G, 140G
12F, 12G, 130G, 140G
5D4165
SHOE
12G, 130G, 140G
12G, 130G, 140G
6G5393
SHOE
12G, 130G
12G, 130G
6G2408
SHOE
12G, 130G, 140B
12G, 130G, 140B
5T2926
SHOE-CIRCLE GUIDE
120G, 120H, 120K, 120K 2, 135H
120G, 120H, 120K, 120K 2, 135H
4Y2572
SHOE
D7G
D7G
6P2647
SHOE
D7G
D7G
8E4501
SHOE-TRACK
OEMS
OEMS
1259106
SHOE-TRACK
OEMS
OEMS
3Q6553
SHOE-TRACK
OEMS
OEMS
1265067
SHOE-TRACK
325C, 330, 330 FM L, 330B, 330B L, 330C, 330C L, 330C MH, OEMS
325C, 330, 330 FM L, 330B, 330B L, 330C, 330C L, 330C MH, OEMS
6I8455
SHOE-TRACK
328D LCR, 330, 330 FM L, 330B L, 330C FM, 330D L, 336D L, OEMS
328D LCR, 330, 330 FM L, 330B L, 330C FM, 330D L, 336D L, OEMS
6Y8180
SHOE-TRACK
325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330C MH, 330D L, 336D, 336D L, 336E L, 336E LH, 336E LN, 336F L, OEMS
325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330C MH, 330D L, 336D, 336D L, 336E L, 336E LH, 336E LN, 336F L, OEMS